Use the operation panel to print the printer's current network settings.
The network settings printout contains important information about your network. Handle it with care.
-
Make sure that the printer is powered on.
-
Load two sheets of A4 or Letter-sized plain paper.
-
Select
Setup on HOME screen.
The menu screen appears.
-
Select
Device settings and press the OK button.
-
Select LAN settings and press the OK button.
If you specify the administrator password, enter the password.
-
Select Confirm LAN settings and press the OK button.
-
Read the message on the screen, select Yes, and then press the OK button.
-
Press the right Function button.
-
Select Yes and press the OK button to start printing.
The printer starts printing network settings information.
The printed network settings information is as follows:
| Item | Description | Setting |
|---|
| Product Information | Product information | – |
| Product Name | Product name | XXXXXXXX |
| ROM Version | ROM version | XXXXXXXX |
| Serial Number | Serial number | XXXXXXXX |
| Wireless LAN | Wireless LAN | Enable/Disable |
| MAC Address | MAC address | XX:XX:XX:XX:XX:XX |
| Infrastructure | Infrastructure | Enable/Disable |
| Connection | Connection status | Active/Inactive |
| SSID | SSID | Wireless LAN SSID |
| Channel *1 | Channel | XX (1 to 11) |
| Encryption | Encryption method | None/WEP/TKIP/AES |
| WEP Key Length | WEP key length (bits) | Inactive/128/64 |
| Authentication | Authentication method | None/auto/open/shared/WPA-PSK/WPA2-PSK |
| Signal Strength | Signal strength | 0 to 100 [%] |
| TCP/IPv4 | TCP/IPv4 | Enable |
| IP Address | IP address | XXX.XXX.XXX.XXX |
| Subnet Mask | Subnet mask | XXX.XXX.XXX.XXX |
| Default Gateway | Default gateway | XXX.XXX.XXX.XXX |
| TCP/IPv6 | TCP/IPv6 | Enable/Disable |
| Link Local Address | Link local address | XXXX:XXXX:XXXX:XXXX
XXXX:XXXX:XXXX:XXXX |
| Link Local Prefix Length | Link local prefix length | XXX |
| Manual Setting | Manual setting | Enable/Disable |
| IP Address *2 | IP address | XXXX:XXXX:XXXX:XXXX
XXXX:XXXX:XXXX:XXXX |
| Subnet Prefix Length *2 | Subnet prefix length | XXX |
| Stateless Address1 *2 | Stateless address 1 | XXXX:XXXX:XXXX:XXXX
XXXX:XXXX:XXXX:XXXX |
| Stateless Prefix Length1 *2 | Stateless prefix length 1 | XXX |
| Stateless Address2 *2 | Stateless address 2 | XXXX:XXXX:XXXX:XXXX
XXXX:XXXX:XXXX:XXXX |
| Stateless Prefix Length2 *2 | Stateless prefix length 2 | XXX |
| Stateless Address3 *2 | Stateless address 3 | XXXX:XXXX:XXXX:XXXX
XXXX:XXXX:XXXX:XXXX |
| Stateless Prefix Length3 *2 | Stateless prefix length 3 | XXX |
| Stateless Address4 *2 | Stateless address 4 | XXXX:XXXX:XXXX:XXXX
XXXX:XXXX:XXXX:XXXX |
| Stateless Prefix Length4 *2 | Stateless prefix length 4 | XXX |
| Default Gateway1 *2 | Default gateway 1 | XXXX:XXXX:XXXX:XXXX
XXXX:XXXX:XXXX:XXXX |
| Default Gateway2 *2 | Default gateway 2 | XXXX:XXXX:XXXX:XXXX
XXXX:XXXX:XXXX:XXXX |
| Default Gateway3 *2 | Default gateway 3 | XXXX:XXXX:XXXX:XXXX
XXXX:XXXX:XXXX:XXXX |
| Default Gateway4 *2 | Default gateway 4 | XXXX:XXXX:XXXX:XXXX
XXXX:XXXX:XXXX:XXXX |
| IPsec *3 | IPsec setting | Active |
| Security Protocol *3 | Security method | ESP/ESP & AH/AH |
| Direct Connection | Direct connection | Enable/Disable |
| Connection | Connection status | Active/Inactive |
| SSID | SSID | Direct Connection SSID |
| Password | Password | Direct Connection password (10 alphanumeric characters) |
| Channel | Channel | 3 |
| Encryption | Encryption method | AES |
| Authentication | Authentication method | WPA2-PSK |
| TCP/IPv4 | TCP/IPv4 | Enable |
| IP Address | IP address | XXX.XXX.XXX.XXX |
| Subnet Mask | Subnet mask | XXX.XXX.XXX.XXX |
| Default Gateway | Default gateway | XXX.XXX.XXX.XXX |
| TCP/IPv6 | TCP/IPv6 | Enable/Disable |
| Link Local Address | Link local address | XXXX:XXXX:XXXX:XXXX
XXXX:XXXX:XXXX:XXXX |
| Subnet Prefix Length *2 | Subnet prefix length | XXX |
| IPsec *3 | IPsec setting | Active |
| Security Protocol *3 | Security method | – |
| Other Settings | Other settings | – |
| Printer Name | Printer name | Printer name (Up to 15 alphanumeric characters) |
| Direct Conn. DevName | Device name for direct connection (Up to 32 characters) | Device name for direct connection |
| WSD Printing | WSD printing setting | Enable/Disable |
| WSD Timeout | Timeout | 1/5/10/15/20 [min] |
| LPD Printing | LPD printing setting | Enable/Disable |
| RAW Printing | RAW printing setting | Enable/Disable |
| Bonjour | Bonjour setting | Enable/Disable |
| Bonjour Service Name | Bonjour service name | Bonjour service name (Up to 52 alphanumeric characters) |
| LLMNR | LLMNR setting | Enable/Disable |
| SNMP | SNMP setting | Enable/Disable |
| DNS Server | Obtain DNS server address automatically | Auto/Manual |
| Primary Server | Primary server address | XXX.XXX.XXX.XXX |
| Secondary Server | Secondary server address | XXX.XXX.XXX.XXX |
| Proxy Server | Proxy server setting | Enable/Disable |
| Proxy Address | Proxy address | XXXXXXXXXXXXXXXXXXXX |
| Proxy Port | Proxy port specification | 1 to 65535 |
| Cert. Fingerprt(SHA-1) | Certificate fingerprint(SHA-1) | XXXXXXXX XXXXXXXX XXXXXXXX
XXXXXXXX XXXXXXXX |
| Cert. Fingerprt(SHA-256) | Certificate fingerprint(SHA-256) | XXXXXXXX XXXXXXXX XXXXXXXX XXXXXXXX
XXXXXXXX XXXXXXXX XXXXXXXX XXXXXXXX |
("XX" represents alphanumeric characters.)
*1 Channel may range from 1 to 11 depending on country or region of purchase.
*2 Network status is only printed when IPv6 is enabled.
*3 Network status is only printed when IPv6 and IPsec settings are enabled.
If your product issue was not resolved after following the steps above, or if you require additional help, please create or log in to your Canon Account to see your technical support options.
Or if you still need help, visit our Canon Community by clicking the button below to get answers:
____________________________________________________________________________________________
