Printing Network Settings

Use the operation panel to print the printer's current network settings.

Important

• The network settings printout contains important information about your network. Handle it with care.

1. Make sure printer is turned on.

2. Load two sheets of A4 or Letter-sized plain paper.

3. Press Setup button.

   The Setup menu screen appears.

4. Select Device settings and press OK button.

5. Select LAN settings and press OK button.

6. Select Print LAN details and press OK button.

   The printer starts printing network settings information.

   The printed network settings information is as follows: (Some setting values are not displayed depending on the printer settings.)

   Item	Description	Setting
   Product Information	Product information	–
   Product Name	Product name	XXXXXXXX
   ROM Version	ROM version	XXXXXXXX
   Serial Number	Serial number	XXXXXXXX
   Wireless LAN	Wireless LAN	Enable/Disable
   Infrastructure	Infrastructure	Enable/Disable
   MAC Address	MAC address	XX:XX:XX:XX:XX:XX
   Connection	Connection status	Active/Inactive
   SSID	SSID	Wireless LAN SSID
   Channel	Channel	XX (1 to 11)
   Encryption	Encryption method	None/WEP/TKIP/AES
   WEP Key Length	WEP key length (bits)	Inactive/128/64
   Authentication	Authentication method	None/auto/open/shared/WPA-PSK/WPA2-PSK
   Signal Strength	Signal strength	0 to 100 [%]
   TCP/IPv4	TCP/IPv4	Enable
   IP Address	IP address	XXX.XXX.XXX.XXX
   Subnet Mask	Subnet mask	XXX.XXX.XXX.XXX
   Default Gateway	Default gateway	XXX.XXX.XXX.XXX
   TCP/IPv6	TCP/IPv6	Enable/Disable
   Link Local Address	Link local address	XXXX:XXXX:XXXX:XXXX XXXX:XXXX:XXXX:XXXX
   Link Local Prefix Length	Link local prefix length	XXX
   Stateless Address1	Stateless address 1	XXXX:XXXX:XXXX:XXXX XXXX:XXXX:XXXX:XXXX
   Stateless Prefix Length1	Stateless prefix length 1	XXX
   Stateless Address2	Stateless address	XXXX:XXXX:XXXX:XXXX XXXX:XXXX:XXXX:XXXX
   Stateless Prefix Length2	Stateless prefix length 2	XXX
   Stateless Address3	Stateless address 3	XXXX:XXXX:XXXX:XXXX XXXX:XXXX:XXXX:XXXX
   Stateless Prefix Length3	Stateless prefix length 3	XXX
   Stateless Address4	Stateless address 4	XXXX:XXXX:XXXX:XXXX XXXX:XXXX:XXXX:XXXX
   Stateless Prefix Length4	Stateless prefix length 4	XXX
   Default Gateway1	Default gateway 1	XXXX:XXXX:XXXX:XXXX XXXX:XXXX:XXXX:XXXX
   Default Gateway2	Default gateway 2	XXXX:XXXX:XXXX:XXXX XXXX:XXXX:XXXX:XXXX
   Default Gateway3	Default gateway 3	XXXX:XXXX:XXXX:XXXX XXXX:XXXX:XXXX:XXXX
   Default Gateway4	Default gateway 4	XXXX:XXXX:XXXX:XXXX XXXX:XXXX:XXXX:XXXX
   IPsec	IPsec setting	Active
   Security Protocol	Security method	ESP/ESP & AH/AH
   Wireless Direct	Wireless direct	Enable/Disable
   MAC Address	MAC address	XX:XX:XX:XX:XX:XX
   Connection	Connection status	Active/Inactive
   SSID	SSID	Wireless Direct SSID
   Password	Password	Wireless Direct password (10 alphanumeric characters)
   Channel	Channel	3
   Encryption	Encryption method	AES
   Authentication	Authentication method	WPA2-PSK
   TCP/IPv4	TCP/IPv4	Enable
   IP Address	IP address	XXX.XXX.XXX.XXX
   Subnet Mask	Subnet mask	XXX.XXX.XXX.XXX
   Default Gateway	Default gateway	XXX.XXX.XXX.XXX
   TCP/IPv6	TCP/IPv6	Enable/Disable
   Link Local Address	Link local address	XXXX:XXXX:XXXX:XXXX XXXX:XXXX:XXXX:XXXX
   Link Local Prefix Length	Link local prefix length	XXX
   IPsec	IPsec setting	Active
   Security Protocol	Security method	–
   Other Settings	Other settings	–
   Printer Name	Printer name	Printer name (Up to 15 alphanumeric characters)
   Wireless Direct DevName	Device name for wireless direct (Up to 32 characters)	Device name for wireless direct
   WSD Printing	WSD printing setting	Enable/Disable
   WSD Timeout	Timeout	1/5/10/15/20 [min]
   LPD Printing	LPD printing setting	Enable/Disable
   RAW Printing	RAW printing setting	Enable/Disable
   Bonjour	Bonjour setting	Enable/Disable
   Bonjour Service Name	Bonjour service name	Bonjour service name (Up to 52 alphanumeric characters)
   LLMNR	LLMNR setting	Enable/Disable
   SNMP	SNMP setting	Enable/Disable
   DNS Server	Obtain DNS server address automatically	Auto/Manual
   Primary Server	Primary server address	XXX.XXX.XXX.XXX
   Secondary Server	Secondary server address	XXX.XXX.XXX.XXX
   Proxy Server	Proxy server setting	Enable/Disable
   Proxy Address	Proxy address	XXXXXXXXXXXXXXXXXXXX
   Proxy Port	Proxy port specification	1 to 65535
   Cert. Fingerprt(SHA-1)	Certificate fingerprint (SHA-1)	XXXXXXXX XXXXXXXX XXXXXXXX XXXXXXXX XXXXXXXX
   Cert. Fingerprt(SHA-256)	Certificate fingerprint (SHA-256)	XXXXXXXX XXXXXXXX XXXXXXXX XXXXXXXX XXXXXXXX XXXXXXXX XXXXXXXX XXXXXXXX

   ("XX" represents alphanumeric characters.)