Scanner Power Verification Chart
Article ID: ART126025 | | | Date published: 05/12/2015 | | | Date last updated: 08/14/2015 |
Description
Solution
Important!
Unfortunately, on some CanoScan scanner models, there is no obvious way to determine if the scanner is getting power
The following table shows what the scanner's reaction is when the power source is connected.
CanoScan Scanner Model |
Scanner's Reaction |
3000F / 3000ex |
CCD Lamp lights up (the light for this one is difficult to see - you must look for the light at an angle) |
3200F | CCD Lamp lights up |
4200F | CCD Lamp lights up |
4400F | CCD Lamp lights up |
5000F | CCD Lamp lights up |
5600F |
The blue power indicator light on the front of the scanner lid will illuminate when the scanner power is turned on. |
8000F |
CCD Lamp lights up |
8400F |
CCD Lamp lights up and the blue power indicator light on the one-touch scanning button panel illuminates. |
8600F |
CCD Lamp lights up and the blue power indicator light on the one-touch scanning button panel illuminates. |
8800F | CCD White LED lights up briefly and the blue power indicator light around the ON/OFF button illuminates. (The Power Switch is on the Top of the scanner lid next to the one-touch buttons.) |
9000F |
There is blue light surrounding the power button. The power button is towards the top-front of the scanner and is the first button on the left. It is labeled as "ON". Once the power button is pressed and the scanner powers on, the power indicator light that surrounds the power button will illuminate
Reaction from the scanner when powered on: |
9900F |
CCD Lamp lights up and the two green power indicator lights, one on the one-touch scanning button panel and one on the scanner lid, illuminate. |
9950F | CCD Lamp lights up and the blue power indicator light illuminates. This light is located just above the one-touch scanning buttons. (There is a Power Button on the Front of the scanner.) |
D1230UF |
CCD Lamp lights up |
D2400UF |
CCD Lamp lights up |
D1250U2(F) |
CCD Lamp lights up (it is difficult to see this light - you must look for the light at an angle) |
D646U(ex) |
CCD Lamp lights up |
D660U |
No reaction (click here to see special note at the bottom) |
FB 320P |
Scan bar moves slightly and the LED lights up briefly. |
FB 620P |
Scan bar moves slightly and the LED lights up briefly. |
FB 620U |
The LED lights up, then the scan bar moves slightly. |
FB 630P |
The LED lights up, then the scan bar moves slightly. |
FB 630U |
No reaction |
FB 630Ui |
No reaction |
LiDE 20 |
Scanner reacts only if the driver is already installed and there are no communications issues (scan bar moves slightly and LED flickers briefly). Disconnecting and reconnecting the USB cable is NOT a valid test to verify power to this scanner. |
LiDE 25 |
Scanner reacts only if the driver is already installed and there are no communications issues (scan bar moves slightly and LED flickers briefly). Disconnecting and reconnecting the USB cable is NOT a valid test to verify power to this scanner. |
LiDE 30 |
Scanner reacts only if the driver is already installed and there are no communications issues (scan bar moves slightly and LED flickers briefly). Disconnecting and reconnecting the USB cable is NOT a valid test to verify power to this scanner. |
LiDE 35 | Scanner reacts only if the driver is already installed and there are no communications issues (scan bar moves slightly and LED flickers briefly). Disconnecting and reconnecting the USB cable is NOT a valid test to verify power to this scanner. |
LiDE 50 | Scanner reacts only if the driver is already installed and there are no communications issues (scan bar moves slightly and LED flickers briefly). Disconnecting and reconnecting the USB cable is NOT a valid test to verify power to this scanner. |
LiDE 60 | Scanner reacts only if the driver is already installed and there are no communications issues (scan bar moves slightly and LED flickers briefly). Disconnecting and reconnecting the USB cable is NOT a valid test to verify power to this scanner. |
LiDE 70 | Scanner reacts only if the driver is already installed and there are no communications issues (scan bar moves slightly and LED flickers briefly). Disconnecting and reconnecting the USB cable is NOT a valid test to verify power to this scanner. |
LiDE 80 | Scanner reacts only if the driver is already installed and there are no communications issues (scan bar moves slightly and LED flickers briefly). Disconnecting and reconnecting the USB cable is NOT a valid test to verify power to this scanner. |
LiDE 600F | Scanner reacts only if the driver is already installed and there are no communications issues (scan bar moves slightly and LED flickers briefly). Disconnecting and reconnecting the USB cable is NOT a valid test to verify power to this scanner. |
LiDE 500F | Scanner reacts only if the driver is already installed and there are no communications issues (scan bar moves slightly and LED flickers briefly). Disconnecting and reconnecting the USB cable is NOT a valid test to verify power to this scanner. |
N1220U |
Scanner reacts only if the driver is already installed and there are no communications issues (scan bar moves slightly and LED flickers briefly). Disconnecting and reconnecting the USB cable is NOT a valid test to verify power to this scanner. |
N1240U |
Scanner reacts only if the driver is already installed and there are no communications issues (scan bar moves slightly and LED flickers briefly). Disconnecting and reconnecting the USB cable is NOT a valid test to verify power to this scanner. |
N650U |
Scanner reacts only if the driver is already installed and there are no communications issues (scan bar moves slightly and LED flickers briefly). Disconnecting and reconnecting the USB cable is NOT a valid test to verify power to this scanner. |
N656U |
Scanner reacts only if the driver is already installed and there are no communications issues (scan bar moves slightly and LED flickers briefly). Disconnecting and reconnecting the USB cable is NOT a valid test to verify power to this scanner. |
N670U |
Scanner reacts only if the driver is already installed and there are no communications issues (scan bar moves slightly and LED flickers briefly). Disconnecting and reconnecting the USB cable is NOT a valid test to verify power to this scanner. |
N676U |
Scanner reacts only if the driver is already installed and there are no communications issues (scan bar moves slightly and LED flickers briefly). Disconnecting and reconnecting the USB cable is NOT a valid test to verify power to this scanner. |
CanoScan D660U Special Note: The CanoScan D660U scanner does not react based on a power connection alone. This means, if the scanner is not connected to a computer, then the scanner will not react when the power is disconnected and then reconnected.