Scanning Film (9900F)
Article ID: ART161106 | | | Date published: 06/09/2015 | | | Date last updated: 08/18/2015 |
Description
Scanning Film (9900F)
Solution
Scanning Film (9900F)
Scanning Films with the Scanner Buttons
This method of scanning is a simple and convenient way to print or load images into photo album programs, all with a single push of a button. With this method, you can scan without adjusting settings each time.
Printing with the [COPY] Button This button is programmed to send the scanned image to a printer. You can scan 35 mm film strips and slides with it. |
Saving Images to the Album Program with the [SCAN] Button This button is programmed to save the scanned image to the ArcSoft PhotoBase album program. You can scan 35 mm film strips and slides with it. |
* | To use the CanoScan Toolbox Copy function, the scanner and printer should be connected to the computer, all powered on, and the drivers should be installed properly and functioning. See the printer's instruction manual for printing preparation procedures. | |
* | You cannot scan films with the [FILE] and [E-MAIL] buttons. | |
* | The scanner buttons are designed to work with CanoScan Toolbox. After you change a CanoScan Toolbox setting, that setting is used to scan the next time a scanner button is pressed. | |
* | To scan 120 and 4" x 5" format films, open ScanGear CS from within an application program and scan in the Advanced Mode. |
Printing with the [COPY] Button |
Prepare the printer for printing. |
The scanner and printer should be connected to the computer, all powered on, and the drivers should be installed properly and functioning. See your printer's instruction manual for the print preparation procedures. |
Remove the protective sheet from the document cover of the scanner. | |||
|
Set the film(s) in the film guide, and position the film guide on the document glass of the scanner. | ||||||||||
|
||||||||||
|
|
|||||||||
The scanner will start automatically and scan the entire film (all frames) on the document glass. All of the scanned frames will print out on the printer when the scan is complete. |
|||||||||
|
After you have finished scanning film, put the protective sheet back on the document cover of the scanner. | ||||||
|
||||||
|
Saving Images to the Album Program with the [SCAN] Button |
Remove the protective sheet from the document cover of the scanner. | |||
|
Set the film in the film guide and position the film guide on the document glass of the scanner. | ||||||||||
|
||||||||||
|
|
|||
The scanner will start automatically and scan the entire film (all frames) on the document glass. All of the scanned frames will open in ArcSoft PhotoBase when the scan is complete. |
|||
* | The scanned image may be added to the sample album the first time you use the ArcSoft PhotoBase album program. To have scanned images saved in your own album, create one in advance. | ||
Save the album. | |
After you have finished scanning film, put the protective sheet back on the document cover of the scanner. | ||||||
|
||||||
|
Scanning Films with CanoScan Toolbox
You can scan 35 mm film strips and slides using the Copy, Save, Scan-1 and Scan-2 buttons in CanoScan Toolbox. The procedures are similar for each button. |
Remove the protective sheet from the document cover of the scanner. | |||
|
Set the film(s) in the film guide, and position the film guide on the document glass of the scanner. | |||||||||
|
|||||||||
|
Start CanoScan Toolbox. |
Click a button on the CanoScan Toolbox main window to open the settings window for that button. | ||||||||||
|
Select a [Select source] option. | |||||
|
|||||
Skip to Step 8 if you selected the Auto mode. |
Set the [Scan mode] if you selected Film in the Select source category. | |||||||
|
Set the [Image quality] if you selected Film in the Select source category. | |||||||||
|
|||||||||
|
Click the [Scan] button. | |
If you selected the Scan all frames option, all frames will automatically be scanned. If you selected Display thumbnails, the image thumbnails will display. If you selected Index scan, all frames on the document glass will be scanned and displayed in an index image. |
If you selected Display thumbnails, place a check mark beside the frames you wish to scan, and click the [Next] button. | |
The selected images will be scanned, loaded into the application and saved. |
After you have finished scanning film, put the protective sheet back on the document cover of the scanner. | |||||||||
|
|||||||||
|
Scanning Films with ScanGear CS in Simple Mode
To scan 35 mm film strips and slides into an application program, you can start ScanGear CS from within the program. In the Simple Mode, there are only a few simple procedures. |
Remove the protective sheet from the document cover of the scanner. | |||
|
Set the film(s) in the film guide, and position the film guide on the document glass of the scanner. | ||||||||||
|
||||||||||
|
Start ScanGear CS from within the application program. |
If ScanGear CS is in the Advanced Mode, click the [Simple Mode] button on the bottom right of the window to display the Simple Mode tab. |
Set the [Select source] category to [Film]. | |
Set the [Type of original]. | |||||
|
Click the [Preview] button. | ||||||||||
Thumbnails of the frames will display. | ||||||||||
|
Place a check mark beside the frames you wish to scan and click the [Scan] button. | |
The frames with check marks will be scanned and sent to the application program as 200 dpi, photo size (8.9 x 12.7 cm/3.5 x 5.0 in.) images. |
After you have finished scanning film, put the protective sheet back on the document cover of the scanner. | |||||||
|
|||||||
|
Scanning Films with ScanGear CS in Advanced Mode
To scan 35 mm film strips and slides, 120 and 4" x 5" format films into an application program, you can start ScanGear CS from within the program. In the Advanced Mode, you can change the resolution and use various functions to scan, including color correction, filters, and a dust and scratch removal function. |
Remove the protective sheet from the document cover of the scanner. | |||
|
Set the film(s) in the film guide, and position the film guide on the document glass of the scanner. | |||||||||||
|
Start ScanGear CS from within the application program. |
If ScanGear CS is in the Simple Mode, click the [Advanced Mode] button on the bottom right of the window to display the Advanced Mode tab. |
Set the [Select source] category corresponding to the film. | |
Set the [Color Mode] category corresponding to the film. | |
Click the [Preview] button. | ||||||||||
Thumbnails of the frames will display. | ||||||||||
|
Place a check mark beside the number(s) of the frame(s) you wish to scan. | ||||||||||||
|
||||||||||||
|
Set the [Output Resolution] and [Scale] to a value that is appropriate for the image's ultimate use. | |||||||||||||||||||||||||||
|
|||||||||||||||||||||||||||
The initial settings for scanning film are 800 dpi for Output Resolution and 100% for Scale. You are recommended to select the following resolutions and scale for the respective uses of the image. | |||||||||||||||||||||||||||
35 mm Films | |||||||||||||||||||||||||||
|
|||||||||||||||||||||||||||
|
Set the other categories as required. | |
Click the [Scan] button. | |
The selected frames will be scanned, loaded into the application and saved. |
After you have finished scanning film, put the protective sheet back on the document cover of the scanner. | |||||||
|
|||||||
|
SIMS Doc Id
0