| Search Results |
 |
Using PC-Free Multi Projection WUX7500 / WUX6700 / WUX5800
|
Using PC-Free Multi Projection A JPEG image on a USB flash drive can be divided among up to nine projectors and combined into a single, large image. When projectors are connected via a wired LAN, the projector that produces the image in the upper left is called the Primary projector and the other eight, Secondary projectors. The image as a whole is controlled by the Primary projector PC-free multi projection is not available over a wireless LAN. This feature is available with the following number of projectors and layout patterns. The projector you assign as the Primary projector, identified in the layout pattern as [1], always projects the upper-left image. Set up the projectors as follows. 1 On each projector, configure installation and image adjustment settings such as edge blending and keystone correction to blend overlapping areas. 2 Connect the projectors with LAN cables and set [Network (wired/ wireless )] to [On/Off] or [On/On (Pj AP)] 3 Configure some projectors as Secondaries. Select [Input settings] > [PC-free multi projection] > [Mode setting] > [Secondary]. Complete this setting on each Secondary projector 4 Configure one projector as the Primary projector. (1) Select [Input settings] > [PC-free multi projection] > [Mode setting] > [Primary]. ( 2 ) Configure the following settings in [PC-free multi projection].
|
|
|
Wireless LAN (Wi-Fi) Legal information WUX7500 / WUX6700 / WUX5800
|
WUX7500/WUX6700/WUX5800 Frequency band(s): 2 ,401 MHz – 2 ,473 MHz Maximum radio-frequency power: 12.7 dBm
|
|
|
Controlling the Projector from a Computer WUX7500 / WUX6700 / WUX5800
|
2 Launch a web browser, enter “http://(projector IP address)” in the address bar, and press the Enter key. ... The factory default IP address is “192.168.254.254” for wired connections and “192.168.253.254” for wireless connections.
|
|
|
Menu Install Settings WUX7500 / WUX6700 / WUX5800
|
Digital image shift > [Install settings] > [Digital image shift] Moves the position of the projected image. When screen aspect is 16:9 D. image shift, move images vertically using the buttons, and for 4:3 D. image shift, move images horizontally using the buttons. This cannot be selected when the screen aspect is 16:9, 16:10 or 4:3. Professional settings Specify advanced installation settings. Menu screen when the Ultra-wide Zoom Lens (RS-SL06UW) is attached RGB alignment Correct color misalignment. Audio is muted while the chart is shown. High altitude Switch the fan mode to suit installation at low or high altitudes (above 2 ,300 m [7,545.8']). Lens shift mode Switch the available lens shift range as needed.
|
|
|
Connecting to a Wired Network Overview WUX7500 / WUX6700 / WUX5800
|
■ Connection Methods The projector can be connected to a wired network with a LAN cable or to a wireless network via Wi-Fi . Wired Networks
|
|
|
Menu Image Adjustment WUX7500 / WUX6700 / WUX5800
|
Brightness Adjust image brightness. Contrast Sharpen or soften image contrast. Sharpness Adjust image sharpness. Gamma Correct image areas that are too dark or too bright to see clearly. Color adjustment Adjust color-related settings such as color level, color balance, and color temperature. In [DICOM SIM] image mode, [Color temperature] is not adjusted with numeric values but set to one of the following five presets. Preset 1: Prioritize brightness, relative to DICOM Standard Part 14. Preset 2 : Prioritize color tone, relative to DICOM Standard Part 14. Preset 3: Adjust color to conform to DICOM Standard Part 14. Preset 4: Reproduce colors of X-ray film (Clear base). Preset 5: Reproduce colors of X-ray film (Blue base). Advanced adjustment Fine-tune noise reduction and color tone. Ambient light Minimize the effect of ambient light on the screen. [Ambient light] is available when the image mode is [Photo/sRGB] Random noise reduction Reduce random image noise*. * Effective on noise with an irregular frequency or amplitude.
|
|
|
Multiple Projectors Corner Adjustment WUX7500 / WUX6700 / WUX5800
|
Corner Adjustment Projected images from multiple projectors used in overlapping projection must be precisely repositioned. Positions of each corner in the blending area can be aligned with the blending area of the reference projector. 1 On the reference projector, configure keystone (P145) and edge-blending settings, and then set the edge-blending markers to [On]. 2 Select [Install settings] > [Professional settings] > [Edge blending] > [Adjust] > [Corner adjustment]. 3 Select a point to adjust, and move it so that the image as a whole looks symmetrical. 4 As you watch the projected images, fine-tune markers of the projector you are adjusting so that they overlap the reference projector markers as much as possible.
|
|
|
Adjusting Keystone Distortion WUX7500 / WUX6700 / WUX5800
|
Adjusting Keystone Distortion Two types of correction are available: horizontal/vertical correction and corner correction. Use horizontal/vertical keystone correction to adjust image width or height
|
|
|
Menu Remote control/Side control WUX7500 / WUX6700 / WUX5800
|
Remote control/Side control Specify which operations are available using buttons on the remote control or in the projector’s side controls. Beep You can select whether a beep sounds or not when you operate the projector. The beep will not sound if you mute the projector sound with the MUTE button on the remote control. Key repeat Key repeat enables projector or remote control buttons to be held down instead of pressing them repeatedly. Key lock Lock the projector or remote ( wireless ) to prevent operation. To Unlock Key Lock Function Turn off the projector and unplug the power plug. Hold down the OK button on the projector and plug in the power cord, as you continue to hold down the OK button. In a moment, a beep will sound, and the controls will be unlocked. When you access this setting from the projector’s side controls, [Main unit] is not available. Similarly, when you access the setting from the remote control, [Remote ( wireless )] is not available. IR receiver settings Select the infrared receiver of the projector. Remote control channel Separate channels can be assigned to up to four projectors so that a single remote control can be used with each projector. Selecting the Projector Channel If a wired remote control is used, there is no need to set the remote control channel Selecting a Channel on the Remote Control After changing the projector channel from the menu, always change the remote control channel accordingly.
|
|
|
Turning the Projector Off WUX7500 / WUX6700 / WUX5800
|
1 Press the POWER button. 2 When this window is displayed, press the POWER button again. After you turn the power off, the projector will enter standby mode once it cools down.
|
|
