| Search Results |
 |
Menu Install Settings WUX7500 / WUX6700 / WUX5800
|
Zoom When the Short Fixed Lens (RS-SL03WF) or the Ultra-wide Zoom Lens (RSSL06UW) is attached and if the projected image does not fit on the screen, you can display the image by electronically reducing its size. This type of zooming reduces overall image dimensions, relative to the center of the image . Press the button on the remote control to project images at a reduced size, and press the button to enlarge images to full size. Images can be projected at 75 – 100% of the original size.
|
|
|
Menu Image Adjustment WUX7500 / WUX6700 / WUX5800
|
Image adjustment This section describes image quality settings such as brightness, contrast, and sharpness. Menu screen when the input signal is HDMI Menus that are not available are grayed out or hidden. * Any adjustments you make are stored for each combination of input signal and image mode. Image mode Select the overall image quality for projected images . Can also be selected by pressing the IMAGE button on the remote control Menus that are not available are grayed out or hidden. You can adjust the image quality by adjusting the following items in each image mode: [Brightness], [Contrast], [Sharpness], [Gamma], [Color adjustment], [Advanced adjustment], and [Lamp mode] Create profile Save desired image quality settings in up to five user profiles.
|
|
|
Using PC-Free Multi Projection WUX7500 / WUX6700 / WUX5800
|
Using PC-Free Multi Projection A JPEG image on a USB flash drive can be divided among up to nine projectors and combined into a single, large image . When projectors are connected via a wired LAN, the projector that produces the image in the upper left is called the Primary projector and the other eight, Secondary projectors. The image as a whole is controlled by the Primary projector PC-free multi projection is not available over a wireless LAN. This feature is available with the following number of projectors and layout patterns. The projector you assign as the Primary projector, identified in the layout pattern as [1], always projects the upper-left image . Set up the projectors as follows. 1 On each projector, configure installation and image adjustment settings such as edge blending and keystone correction to blend overlapping areas. 2 Connect the projectors with LAN cables and set [Network (wired/wireless)] to [On/Off] or [On/On (Pj AP)] 3 Configure some projectors as Secondaries. Select [Input settings] > [PC-free multi projection] > [Mode setting] > [Secondary]. Complete this setting on each Secondary projector 4 Configure one projector as the Primary projector. (1) Select [Input settings] > [PC-free multi projection] > [Mode setting] > [Primary]. (2) Configure the following settings in [PC-free multi projection].
|
|
|
Connecting to a Wired Network Overview WUX7500 / WUX6700 / WUX5800
|
■ Network Connection Overview Connecting the projector to a network enables you to control the projector from a computer and receive notification of projector errors via email. Depending on the method of network connection, preparation on the computer side may be necessary.
|
|
|
High Installation, Ceiling Mounting, and Rear Projection WUX7500 / WUX6700 / WUX5800
|
In [Image flip H/V] (P143) in the menu, choose a method of projection that corresponds to how the projector is installed. 1 Press the MENU button on the remote control or projector, and then select [Install settings] > [ Image flip H/V]. 2 Select the orientation of how the projector is installed.
|
|
|
Menu System settings WUX7500 / WUX6700 / WUX5800
|
Menu screen when the input signal is HDMI Menus that are not available are grayed out or hidden. User screen settings Capture a logo and specify logo display settings. Logo capture Registers the current image as a user logo. Registered user logos can be shown when no signal is received, when the BLANK button is pressed, or as the startup image . Only images at an aspect ratio of 16:10 can be registered as user logos. Logo position Specify the position of registered user logos. You can specify the position after a logo has been registered. Choose from upper left, upper right, center, lower left, or lower right. No signal screen Customize the screen shown when no input signals are received. Screen when blank Select the screen shown when projection is temporarily blanked out by pressing the BLANK button on the remote control . Projector on Select a logo to project after startup until input signals can be projected. On screen Specify display details for on-screen menus, help, and warning or precaution icons. Menu position Reposition menu display. Choose from upper left, upper right, center, lower left, or lower right. Only [Center] is available when edge blending is used. Other display positions are grayed out and not available. Menu display time Extend menu display from the standard 10 or 30 seconds to 3 minutes. The following display times are also changed. Guide Shows the guide screen.
|
|
|
Error Notification Mails WUX7500 / WUX6700 / WUX5800
|
|
Relationship Between Projecting Distance and Image Size WUX7500 / WUX6700 / WUX5800
|
|
Projecting Images on a USB Flash Drive WUX7500 / WUX6700 / WUX5800
|
|
Maintenance Cleaning the Projector
|
Clean the projector frequently to prevent dust from settling on the surface. A dirty lens may ruin the quality of the projected image .
|
|
|
