Setting the IP Address Using NetSpot Device Installer
IMPORTANT:
If Windows Firewall is enabled
- We recommend that you set the IP address using the ARP/PING command or the Printer Status Window.
- If you want to set the IP address using NetSpot Device Installer, you need to add "NetSpot Device Installer" to Windows Firewall in advance. Perform either of the following procedures.
- Adding "NetSpot Device Installer" to the [Exceptions] sheet in the [Windows Firewall] dialog box (For more details, see Readme of NetSpot Device Installer. To display the Readme, click [ 
] in [NetSpot Device Installer for TCP/IP] in the [Additional Software Programs] screen in CD-ROM Setup.)
- Installing NetSpot Device Installer (You can add it to Windows Firewall during the installation.)
NOTE:
If you changed the IP address after installing the printer driver
- Specify the port to be used again in the printer driver. For details on the procedure for setting a port, see "e-Manual" (HTML manual) in the CD-ROM supplied with the printer.
Setting the IP Address Using NetSpot Device Installer
This section describes the procedure for using NetSpot Device Installer without installing it. For details on installing NetSpot Device Installer, see "e-Manual" (HTML manual) in the CD-ROM supplied with the printer.
1. Make sure that the LAN cable is connected properly, and the printer is turned ON.
2. Turn the computer on, and then log on to Windows as a user with administrative rights.
3. Insert the supplied CD-ROM "LBP6300 User Software" into the CD-ROM drive of your computer.
4. Click [Additional Software Programs].
NOTE:
If the above screen does not appear
If the [AutoPlay] dialog box appears
If the [User Account Control] dialog box appears
- Click [Continue] or [Yes].
5. Click [Start] for [NetSpot Device Installer for TCP/IP].
If [License Agreement] appears, read the contents, and then click [Yes].
6. Set the IP address.
NOTE:
MAC address location
The MAC address is listed at (A) on the printer.
1. Select the device.
2. Set the IP address.
| When obtaining an IP address using DHCP (The DHCP server needs to be running.) |
Select [IP Address Settings] m² [DHCP] from the [Device] menu.  |
| When assigning an IP address using IP Address Pool (IP Address Pool needs to be specified.) |
Select [IP Address Settings] m² [IP Address Pool] from the [Device] menu. 
* For more details on IP Address Pool, see Help of NetSpot Device Installer. (Help is displayed by clicking [Help] in the [Help] menu.) |
| When setting an IP address directly |
(1) Select [IP Address Settings] m² [Manual Setting] from the [Device] menu.
(2) Enter the IP address of the printer.
(3) Click [OK].
 |
3. When the message <The device has been reset.> appears, click [OK].
Wait for approximately 20 seconds or longer as is after clicking [OK].
After completing the reset, the settings are enabled.
1. Select the device.
2. Select [Protocol Settings] from the [Device] menu.
3. Set the IP address.
- Specify each setting.
- Click [OK].
| [IP Address Setting with] |
Select the method for setting the IP address.
· [Manual Setting]: Allows you to specify the IP address directly. The IP address entered in [IP Address] is set for the printer.
· [Auto Detect]: Obtains an IP address using RARP, BOOTP, or DHCP.
- [RARP]: Obtains an IP address using RARP. (The RARP daemon needs to be running.)
- [BOOTP]: Obtains an IP address using BOOTP. (The BOOTP daemon needs to be running.)
- [DHCP]: Obtains an IP address using DHCP. (The DHCP server needs to be running.) |
| [IP Address] |
Enter the IP address of the printer. |
| [Subnet Mask] |
Enter the subnet mask as needed. |
| [Gateway Address] |
Enter the gateway address as needed. |
NOTE:
When selecting [RARP]
- You cannot enter any values in [IP Address].
When selecting [BOOTP] or [DHCP]
- You cannot enter any values in [IP Address], [Subnet Mask], and [Gateway Address].
If you cannot use RARP, BOOTP, or DHCP
- Specify the settings in [Manual Setting].
4. When the message <The device has been reset.> appears, click [OK].
Wait for approximately 20 seconds or longer as is after clicking [OK].
After completing the reset, the settings are enabled.
A device on the network may have the same IP address as that set for the printer. In this case, perform the following procedure.
1. Turn OFF the device that has the same IP address or remove the device from the network.
2. Repeat the procedure from the beginning.
3. After completing the settings for this printer, restore the devices to their original states.
* If you cannot set the IP address using NetSpot Device Installer including the case where this procedure is not possible, set the IP address using the ARP/PING command.
Displaying the CD-ROM Top Page
If the CD-ROM top page does not appear even after inserting the CD-ROM, perform the following procedure.
* The CD-ROM drive name is indicated as "D:" in this manual. The CD-ROM drive name may differ depending on the computer you are using.
1. From the [Start] menu, select [Run].
2. Enter "D:\English\MInst.exe."
3. Click [OK].
1. Enter "D:\English\MInst.exe" in [Start Search] or [Search programs and files] under the [Start] menu.
2. Press the [ENTER] key on the keyboard.
Back
