Setting Network (SX80 II)

Displaying the Network Configuration Screen

1 Turn on the computer and projector.

2 Launch a web browser, enter "http://192.168.254.254" in the address bar, and press the Enter key. The password input screen appears. The supported web browsers is Microsoft Internet Explorer 6 or later.

3 In the password input screen, enter "root" for [User name] and "system" for [Password] and click the [OK] button.

The projector network configuration screen appears on the web browser. The following information is displayed.

[Projector name]: The name of the projector on the network

[Location]: The location of the projector

[MAC address]: The MAC address of the projector

[IP address]: The IP address of the projector

[Power Status]: The power status of the projector

[Lamp Time Normal Mode]:The total lamp used time in its normal mode

[Lamp Time Quiet Mode]: The total lamp used time in its quiet mode

[Lamp Time Converted]: The total lamp used time (converted value)

[Filter Time]: The total filter used time

Click the [Settings] button to display the menu screen.

Setting the Network

1 In the menu screen, click [Password], input the new user name and password, and click the [OK] button.

Setting items:

[User name]: The user name for logging in the network

[New password]: The new password

[Confirm new password]: The password for confirmation

2 Click [TCP/IP], enter appropriate values in the following field, and click the [OK] button.

Setting items:

[IP address]: The IP address of the projector

[Subnet mask]: The subnet mask of the projector

[Default gateway]: The default gateway of the projector

3 Click [Mail], enter appropriate values in the following field for the error report, and click the [OK] button.

Setting items:

[To:]: The E-mail address to which the error report is sent (Within 63 alphanumeric characters)

[Cc:]: The E-mail address to which the carbon copy of the error report is sent (Within 63 alphanumeric characters, can be omitted)

[From:]: The sender of the E-mail (the projector)

[SMTP server IP address]: The IP address of the available SMTP mail server

[SMTP server port number]:The port number of the available SMTP mail server

[SNTP server IP address]: The IP address of the available SNTP mail server can be omitted)

[Time zone]: The time zone of the installation site

[Mail resend interval]: The E-mail resending interval at a transmission failure Setting range: 0 - 59 seconds (the factory default: 10 seconds)

[Mail resend times]: The number of E-mail resending attempts at a transmission failure Setting range: 0 - 255 times (the factory default: 3 times)

[Error report]: Turning ON/OFF the error report sending function (the factory default: [OFF])

4 If the SMTP mail server authentication is required, click [Mail auth], enter appropriate values in the following field, and click the [OK] button.

Select one of the following four authentication method in [Mail authentication]. Select [OFF] if the mail authentication is not required (the factory default is [OFF]).

[LOGIN (SMTP authentication)], [CRAM-MD5 (SMTP authentication)], [USER/PASS (POP before SMTP)], [APOP (POP before SMTP)]

Setting items:

[User name]: The user name for the mail authentication

[Password]: The password for the mail authentication

[Confirm password]: The password for confirmation

[POP3 server IP address]: The IP address of the POP3 server

[POP3 server port number]: The port number of the POP3 server (The factory default: 110)

[POP before SMTP response time]: The wait time between the POP3 authentication and the transmission to the SMTP mail server (millisecond, the factory default: 300)

5 If you want to monitor the projector, click [SNMP], enter appropriate values in the following field, and click the [OK] button.

Select one of the following four SNMP version in [SNMP]. Select [OFF] if you don't want to monitor the projector.

(The factory default: [OFF])

[V1], [V2c], [V3 (MD5)], [V3 (DES, MD5)]

Setting items:

[Receive community]: The name of the community (user)

[Password]: The password for the community setting

[Confirm password]: The password for confirmation

[SNMP trap]: Conditions for sending the SNMP trap

[Trap IP address]: The IP address to which the SNMP trap is sent

[Trap community]: The name of the community (user) to which the SNMP trap is sent

What is the SNMP Agent Function?

This projector supports the SNMP (Simple Network Management Protocol) agent function that monitors the status of the projector. SNMP consists of the manager (a monitoring tool, your PC) and agent (a monitored target, the projector). The information exchange group via SNMP is called "a community." The message which tells the status of the agent is called "a SNMP trap."

This projector has the following SNMP traps:

• Cold start: it tells the SNMP agent is under initialization.
• Warm start: it tells the SNMP agent is under reset (at the SNMP version upgrade).
• Authentication failure: it tells that it failed the SNMP authentication.
• Faulty lamp: it tells that a lamp-related error was occurred.
• Faulty power supply: it tells that a power supply-related error was occurred.
• Temperature abnormality: it tells that a temperature-related error was occurred.
• Lamp status change: it tells that the status of the lamp used time was changed.
• Faulty cooling fan: it tells that a cooling fan-related error was occurred.
• Faulty lamp cover: it tells that a lamp cover-related error was occurred.
• Filter message: it tells that the air filter has reached its replacement timing.
• Unknown: it tells that an unknown error was occurred.

Make sure to install the SNMP manager program on your PC before using the SNMP agent function.

Authentication and Encryption Protocols

SNMP V3 for the projector uses the DES-CBC for the authentication and encryption protocols.

6 Click [Projector info] and enter the projector name.

• You can input 1 to 63 alphanumeric characters.
• The factory default is [SX80 MarkII].

7 Click [Location], enter the projector location, and click the [OK] button.

• You can input up to 63 alphanumeric characters.
• The factory default is blank.

8 Click [Apply] when you have completed each menu.

Click the [OK] button when the following dialog box is displayed.

The network setting of the projector is now completed.

If you want to test the error report transmission, click [Send test mail].

---

Resetting the Network Setting

1 Click [Initialize] in the menu screen.

2 Click the [OK] button when the following dialog box is displayed.

If you want to restore to the factory setting from the projector, perform [Network setting initialization] from the menu.