Ask a Question

Scanner Power Verification Chart

Article ID: ART126025 | Date published: 05/12/2015 | Date last updated: 08/14/2015
 

Description

Scanner Power Verification Chart

Solution

New Page 2

Important!
Unfortunately, on some CanoScan scanner models, there is no obvious way to determine if the scanner is getting power

The following table shows what the scanner's reaction is when the power source is connected.

CanoScan Scanner Model

Scanner's Reaction

3000F / 3000ex

CCD Lamp lights up (the light for this one is difficult to see - you must look for the light at an angle)
3200F CCD Lamp lights up
4200F CCD Lamp lights up
4400F CCD Lamp lights up
5000F CCD Lamp lights up

5600F

The blue power indicator light on the front of the scanner lid will illuminate when the scanner power is turned on.

Scanner bar and light reacts only if the driver is already installed and the scanner is properly detected. If detected, the scan bar moves slightly and the CCD White LED lights up briefly.
(The Power Button is on the Right Side of the scanner near the back.)

8000F

CCD Lamp lights up

8400F

CCD Lamp lights up and the blue power indicator light on the one-touch scanning button panel illuminates.
(There is a Power Button on the Side of the scanner.)

8600F

CCD Lamp lights up and the blue power indicator light on the one-touch scanning button panel illuminates.
(There is a Power Button on the Right Side of the scanner near the front.)
8800F CCD White LED lights up briefly and the blue power indicator light around the ON/OFF button illuminates.
(The Power Switch is on the Top of the scanner lid next to the one-touch buttons.)
9000F There is blue light surrounding the power button. The power button is towards the top-front of the scanner and is the first button on the left. It is labeled as "ON". Once the power button is pressed and the scanner powers on, the power indicator light that surrounds the power button will illuminate

Reaction from the scanner when powered on:
Scanner bar moves slightly and the White LED lights up briefly.
(The Power Button is on the Left-Front of the scanner lid.)

9900F

CCD Lamp lights up and the two green power indicator lights, one on the one-touch scanning button panel and one on the scanner lid, illuminate.
(There is a Power Button on the Front of the scanner.)
9950F CCD Lamp lights up and the blue power indicator light illuminates. This light is located just above the one-touch scanning buttons.
(There is a Power Button on the Front of the scanner.)

D1230UF

CCD Lamp lights up

D2400UF

CCD Lamp lights up

D1250U2(F)

CCD Lamp lights up (it is difficult to see this light - you must look for the light at an angle)

D646U(ex)

CCD Lamp lights up

D660U

No reaction (click here to see special note at the bottom)

FB 320P

Scan bar moves slightly and the LED lights up briefly.

FB 620P

Scan bar moves slightly and the LED lights up briefly.

FB 620U

The LED lights up, then the scan bar moves slightly.

FB 630P

The LED lights up, then the scan bar moves slightly.

FB 630U

No reaction

FB 630Ui

No reaction

LiDE 20

Scanner reacts only if the driver is already installed and there are no communications issues (scan bar moves slightly and LED flickers briefly). Disconnecting and reconnecting the USB cable is NOT a valid test to verify power to this scanner.

LiDE 25

Scanner reacts only if the driver is already installed and there are no communications issues (scan bar moves slightly and LED flickers briefly). Disconnecting and reconnecting the USB cable is NOT a valid test to verify power to this scanner.

LiDE 30

Scanner reacts only if the driver is already installed and there are no communications issues (scan bar moves slightly and LED flickers briefly). Disconnecting and reconnecting the USB cable is NOT a valid test to verify power to this scanner.
LiDE 35 Scanner reacts only if the driver is already installed and there are no communications issues (scan bar moves slightly and LED flickers briefly). Disconnecting and reconnecting the USB cable is NOT a valid test to verify power to this scanner.
LiDE 50 Scanner reacts only if the driver is already installed and there are no communications issues (scan bar moves slightly and LED flickers briefly). Disconnecting and reconnecting the USB cable is NOT a valid test to verify power to this scanner.
LiDE 60 Scanner reacts only if the driver is already installed and there are no communications issues (scan bar moves slightly and LED flickers briefly). Disconnecting and reconnecting the USB cable is NOT a valid test to verify power to this scanner.
LiDE 70 Scanner reacts only if the driver is already installed and there are no communications issues (scan bar moves slightly and LED flickers briefly). Disconnecting and reconnecting the USB cable is NOT a valid test to verify power to this scanner.
LiDE 80 Scanner reacts only if the driver is already installed and there are no communications issues (scan bar moves slightly and LED flickers briefly). Disconnecting and reconnecting the USB cable is NOT a valid test to verify power to this scanner.
LiDE 600F Scanner reacts only if the driver is already installed and there are no communications issues (scan bar moves slightly and LED flickers briefly). Disconnecting and reconnecting the USB cable is NOT a valid test to verify power to this scanner.
LiDE 500F Scanner reacts only if the driver is already installed and there are no communications issues (scan bar moves slightly and LED flickers briefly). Disconnecting and reconnecting the USB cable is NOT a valid test to verify power to this scanner.

N1220U

Scanner reacts only if the driver is already installed and there are no communications issues (scan bar moves slightly and LED flickers briefly). Disconnecting and reconnecting the USB cable is NOT a valid test to verify power to this scanner.

N1240U

Scanner reacts only if the driver is already installed and there are no communications issues (scan bar moves slightly and LED flickers briefly). Disconnecting and reconnecting the USB cable is NOT a valid test to verify power to this scanner.

N650U

Scanner reacts only if the driver is already installed and there are no communications issues (scan bar moves slightly and LED flickers briefly). Disconnecting and reconnecting the USB cable is NOT a valid test to verify power to this scanner.

N656U

Scanner reacts only if the driver is already installed and there are no communications issues (scan bar moves slightly and LED flickers briefly). Disconnecting and reconnecting the USB cable is NOT a valid test to verify power to this scanner.

N670U

Scanner reacts only if the driver is already installed and there are no communications issues (scan bar moves slightly and LED flickers briefly). Disconnecting and reconnecting the USB cable is NOT a valid test to verify power to this scanner.

N676U

Scanner reacts only if the driver is already installed and there are no communications issues (scan bar moves slightly and LED flickers briefly). Disconnecting and reconnecting the USB cable is NOT a valid test to verify power to this scanner.

CanoScan D660U Special Note: The CanoScan D660U scanner does not react based on a power connection alone. This means, if the scanner is not connected to a computer, then the scanner will not react when the power is disconnected and then reconnected.

SIMS Doc Id

0

Rate this Article
Was this article helpful?
Yes, This document is helpful
No, This document needs a clearer explanation
 
Please provide your comments