How to change the connection method from USB to wireless (Macintosh)

The environment necessary for the wireless connection

Before connecting this printer to the network, confirm the following two items, (A) and (B).

(A) Access point or router (supporting IEEE802.11b/g/n)

An access point or router is a relay device which connects not only the Internet and network devices such as a computer or printer, but also one network device to another.

So, your access point or router must be properly set before you go to the next setup step.

(B) The computer to be used with the printer must be connected to the network.

In order to confirm whether the computer to be used with the printer is connected to the network, try to browse the Internet website from the computer.

REFERENCE

An "Ad-hoc connection," which establishes a direct connection to the computer over a wireless connection without an access point, is not supported. Be sure to prepare an access point.

 

The procedures for the wireless connection

In order to use the printer in a wireless connection, follow the procedures below.

In order to use the printer in a wireless connection even after the USB connection is completed, follow the procedures below to perform the wireless setup again.

1. Select the wireless setup method.
   To use the printer in a wireless connection, select the wireless setup method you prefer.
    
2. Perform the wireless setting from the operation panel.
   Perform the setting based on the setup method you selected in the step 1 using the operation panel.
    
3. Install the software.
   Install the software into the computer used with the printer.
    
4. Perform the test printing.
   Try wireless printing to confirm whether the wireless setup has been performed properly.

1. Select the wireless setup method

To use the printer in the wireless connection, first select the wireless setup method.

- Standard setup connection:

Perform the wireless setup manually.

In most cases, you can create a wireless environment using this setup method.

- WPS connection:

If the access point or the router you are using supports the WPS function, you can use this setup method to connect the printer in a wireless connection.

Confirm that the access point or the router you are using has the WPS button.

REFERENCE

 

• There is the WPS mark
  on the access point or the router you are using if it supports the WPS function.

 

 

2. Perform the wireless setup depending on the setup method

IMPORTANT:

 

• Quit all applications before installation.
• Internet connection may be required during the installation. Connection fees apply.

 

 

Screens are based on Mac OS X v.10.7. Actual screens may differ depending on the OS version.

1. Insert the CD-ROM into the computer.
   
    
   
   IMPORTANT:
   If the USB cable is already connected, unplug it. If a message appears on the computer, click Cancel.
    
2. Double-click the Setup icon of the CD-ROM folder to proceed to the following screen. Enter your administrator name and password, then click OK.
   
   
   
   
   If the CD-ROM folder does not open automatically, double-click the CD-ROM icon on the desktop.
   
   
   If you do not know your administrator name or password, click the Help button , then follow the on-screen instructions.
   
   
   REFERENCE:
   If the CD-ROM does not autorun:
   Double-click the CD-ROM icon on the desktop.
    
3. Select which language to use with this program and then click Next.
   
   
    
4. Click Change Connection Method.
   
    
   
   
   IMPORTANT: The Setup Guide will launch in a window on the computer screen (as shown below in step 6). The Setup Guide includes instructions to set up the printer in WPS mode. Follow the instructions on each Setup Guide window pressing the appropriate buttons on the printer's operation panel. Then click the Next button to proceed to the next Setup Guide window. Now go to step 6.
    
5. At Connection Method Selection window, click Network Connection.
   
   
    
6. At Connection Method Selection window, click Wireless Connection.
   
   
    
7. At Preparation for Connection window, ensure the printer is powered on. If it is not powered on, press the ON button and then click Next on the Setup Guide window.
   
   
    
8. At step 2-1 in Printer Setup window, click Next.
   
   
    
9. At step 2-2 in Printer Setup window, press the MENU button on the printer and then click Next.
   
   
    
10. At step 2-3 in Printer Setup window, use the up, down, left and right arrows on the printer to select Wireless LAN setup then press the OK button. The Wi-Fi light will illuminate in blue, and then click Next on the Setup Guide.
    
    
    
     
11. The printer will automatically search for WPS enabled access point / wireless router.
    
     
    
    When the screen left above is displayed, go to the step (A).
    When the screen right above is displayed, go to the step (B).
    
    
    (A) Click Push Button Method.
    
     
    
    -> Go to 8.
    
    
    (B) Click Other Methods.
    
     
    
    Click WPS.
    
     
    
    
    - Standard setup connection:
    Click Other Methods.
    
     
    
    
    Click Standard setup.
    
    
     
12. Follow the instruction until the screen below is displayed.
    Network connection setting is complete.
    Click Next.
    
    

Install the Software (Information)

Let's perform the software installation.

1. At the Software Installation List screen, select the items to install and then click Next.
   
    
   
   REFERENCE:
   Easy-WebPrint EX
   Easy-WebPrint EX is Web print software that is installed on the computer when installing the supplied software. Internet Explorer 7 or later (Windows) is required to use this software. An Internet connection is required for installation.
   
   Follow any on-screen instructions to proceed with the software installation.
    

2. Click Add Printer.
   
    
   
   REFERENCE
   The alphanumeric characters after Canon xxx series is the machine's Bonjour service name or MAC address.
   If the machine is not detected, make sure of the following.

   • The machine is turned on.

   • The firewall function of any security software is turned off.

   • The computer is connected to the access point.
     
     REFERENCE:
     XXX: xxx refers to the model name you are using.

3. Select Canon xxx series Canon IJ Network and click Add.

   
   

   CAUTION:

   If you will be installing the Canon printer driver on Mac OS X and using the printer through a network connection, you can select [Bonjour] or [Canon IJ Network] in the [Add Printer] dialog.

   If [Bonjour] is selected, remaining ink level messages may differ from those indicated by [Canon IJ Network].

   Canon recommends you to use [Canon IJ Network] for printing.

    

    

    

   
    

4. Click Next.
   
    
   
   REFERENCE:
   
   

   • When this printer has not been detected, the Check Printer Settings dialog box is displayed. In such a case, refer to [ The printer cannot be detected (the message that the printer could not be detected on the network is displayed) ].
      
5. Click Exit to complete the installation.
   
   Remove the Setup CD-ROM and keep it in a safe place.
   
   
    
6. Solution Menu EX starts.
   
    
   
   The end of the procedure of the wireless LAN setup.