Borderless Copying
There are two ways (normal / high speed) to make copies.
"Fit to Page" function allows you to make borderless copies of photos.
Normal copies
Use Normal copying for photo copy quality or documents that contain text and photos.
- Confirm that the printer is powered on and open the paper output tray.
The illustration shows an MP170.
- Load paper in the auto sheet feeder (ASF) with the short-side down.
- Lift the document cover and place a document on the platen glass.
Note:
* Regardless of the document size, place it with the long-side toward you.
* Place the document face down on the platen glass.
* Align the document with the alignment mark (shown as the arrow) on the lower right corner of the platen glass.
* The machine cannot scan the area within approximately 3 mm of the front and right edges of the platen glass.
< 1 > Alignment Mark
- Gently close the document cover.
- Press the <Paper> button repeatedly until the preferred paper size and type is illuminated. The options are as follows:
8.5" x 11"
Plain Paper
8.5" x 11"
Photo Paper
4" x 6"
Photo Paper
- Press the <+> button to select the number of copies. (The maximum number of copies is 9.)
- To start copying, press the <Color> or <Black> button.
- To cancel copying, press the <Stop/Reset> button.
High speed copies
High speed copying is suitable for text-only documents.
- Confirm that the printer is powered on and open the paper output tray.
The illustration shows an MP170.
- Load paper in the auto sheet feeder (ASF) with the short-side down.
- Lift the document cover and place a document on the platen glass.
Note:
* Regardless of the document size, place it with the long-side toward you.
* Place the document face down on the platen glass.
* Align the document with the alignment mark (shown as the arrow) on the lower right corner of the platen glass.
* The machine cannot scan the area within approximately 3 mm of the front and right edges of the platen glass.
< 1 > Alignment Mark
- Gently close the document cover.
- Press the <Paper> button to select [8.5" x 11" Plain Paper].
- Press the <+> button to select the number of copies. (The maximum number of copies is 9.)
- Press and hold down the <Color> or <Black> button for 2 seconds or more.
- When the number of copies in the LED disappears and reappears, release the button. The machine starts high speed copying.
- To cancel copying, press the <Stop/Reset> button.
Fit-to-Page
This feature enables you to copy images in the size you set by reducing or enlarging them automatically. The size may not be detected properly dependent on document type. In this case, make a copy through the software using MP Navigator.
- Confirm that the printer is powered on and open the paper output tray.
The illustration shows an MP170.
- Load paper in the auto sheet feeder (ASF) with the short-side down.
- Lift the document cover and place a document on the platen glass.
Note:
* Regardless of the document size, place it with the long-side toward you.
* Place the document face down on the platen glass.
* Align the document with the alignment mark (shown as the arrow) on the lower right corner of the platen glass.
* The machine cannot scan the area within approximately 3 mm of the front and right edges of the platen glass.
< 1 > Alignment Mark
- Gently close the document cover.
- Press the <Paper> button to select [8.5" x 11" Photo Paper] or [4" x 6" Photo Paper].
Note:
* If you select Photo Paper, the machine copies the entire image without borders.
* If you select 8.5" x 11" Plain Paper, making high speed copies is possible.
- Press the <+> button repeatedly to select the number of copies. (The maximum number of copies is 9.)
- Press the <Fit to Page> button to light the Fit-to-Page lamp.
Note: To cancel the Fit-to-Page copying, press the Fit to Page button again.
- To starts Fit-to-Page copying, press the <Color> or <Black> button.
- To cancel copying, press the <Stop/Rest> button.
