| Search Results |
 |
2018 CANON PROJECTOR LINE-UP
|
Canon provides skilled technicians to support our entire line of professional projectors. This small group of dedicated professionals has years of experience assisting customers with every aspect of their A/V needs. From the simplest of setups, to the most complex configurations, we are here to answer your questions.
|
|
 |
How to Set RS-232C Settings on the WUX10
|
While the WUX10 does have an RS-232 connection and codes as you mentioned, CITS does not assist in the use of them.
|
|
|
Menu Install Settings WUX7500 / WUX6700 / WUX5800
|
Install settings Adjust projection to suit the screen or the type of images, or how the projector is installed. Menu screen when the input signal is HDMI Menus that are not available are grayed out or hidden. Positional lock Operation of installation-related functions can be prohibited. • Image flip H/V • Save position (in [Lens - Position]) • Professional settings • Screen aspect • Focus adjustment • Zoom • Lens shift reset • Lens shift adjustment • Keystone • Digital image shift • Zoom adjustment
|
|
|
Here are some common troubleshooting tips for the LV-X2
|
Before calling your dealer or service center for assistance , check the following: 1. Make sure you have connected a projector to your computer or video equipment as described in the section "CONNECTING THE PROJECTOR"
|
|
|
Multiple Projectors Corner Adjustment WUX7500 / WUX6700 / WUX5800
|
Corner Adjustment Projected images from multiple projectors used in overlapping projection must be precisely repositioned. Positions of each corner in the blending area can be aligned with the blending area of the reference projector. 1 On the reference projector, configure keystone (P145) and edge-blending settings, and then set the edge-blending markers to [On]. 2 Select [Install settings] > [ Professional settings] > [Edge blending] > [Adjust] > [Corner adjustment]. 3 Select a point to adjust, and move it so that the image as a whole looks symmetrical. 4 As you watch the projected images, fine-tune markers of the projector you are adjusting so that they overlap the reference projector markers as much as possible.
|
|
|
Menu System settings WUX7500 / WUX6700 / WUX5800
|
Menu screen when the input signal is HDMI Menus that are not available are grayed out or hidden. User screen settings Capture a logo and specify logo display settings. Logo capture Registers the current image as a user logo. Registered user logos can be shown when no signal is received, when the BLANK button is pressed, or as the startup image. Only images at an aspect ratio of 16:10 can be registered as user logos. Logo position Specify the position of registered user logos. You can specify the position after a logo has been registered. Choose from upper left, upper right, center, lower left, or lower right. No signal screen Customize the screen shown when no input signals are received. Screen when blank Select the screen shown when projection is temporarily blanked out by pressing the BLANK button on the remote control. Projector on Select a logo to project after startup until input signals can be projected. On screen Specify display details for on-screen menus, help , and warning or precaution icons. Menu position Reposition menu display. Choose from upper left, upper right, center, lower left, or lower right. Only [Center] is available when edge blending is used. Other display positions are grayed out and not available. Menu display time Extend menu display from the standard 10 or 30 seconds to 3 minutes. The following display times are also changed. Guide Shows the guide screen.
|
|
|
Manual Adjustment to Correct Registration REALis 4K6020Z / 4K5020Z
|
Any manual adjustment values set before switching to 5-point adjustment are cleared. 1 In the [Install settings] menu, select [ Professional settings] > [RGB alignment] > [Advanced registration] > [Adjust] > [Manual adjustment]. The projector enters manual adjustment mode, and a chart is displayed.
|
|
|
Power Management mode
|
image appears and the countdown begins. After the countdown, the lamp will be off. This function helps to save power consumption and extend the lamp life.
|
|
|
Projecting from Multiple Projectors at Once (Edge Blending) WUX7500 / WUX6700 / WUX5800
|
Keep in mind when projecting from multiple projectors that each unit may have a different color balance. Thus, even with the same model, differences in color may be noticeable. 1 Select [Install settings] > [ Professional settings] > [Edge blending] > [Adjust]. 2 Set [Marker] to [On]. Marker lines are projected on the images. The red marker indicates the start position for adjustment, and the green marker, the end position. Initially, only the red marker is visible when you prepare for edge blending, because it is projected over the green marker 3 In [Side], select [Start position] and use the buttons to move the start marker to the outer edge of the overlapping area. Do this for each edge; on the top, bottom, left, and right. 4 Select [Width] and use the buttons to move the end marker to the inner edge of the overlapping area. Do this for each edge; on the top, bottom, left, and right. The area between the starting and ending markers is called the blending area. Shading is applied to this area, and the brightness is adjusted to match portions that overlap with other areas. After you complete settings for one image, do the same thing for the other one to specify the blending area. Adjust the settings to make the blending area for each image the same. 5 Set [Marker] to [Off].
|
|
|
Adjusting Projected Images with Partial Distortion Correction REALis 4K6020Z / 4K5020Z
|
Select one of the 54 adjustment points (in a 6 x 9 grid) for precise distortion correction. 1 In the [Install settings] menu, select [ Professional settings] > [Partial distortion correction] > [Adjust] The projector enters partial distortion correction point selection mode, and a window is displayed for selection of areas to correct.
|
|
|
