Wi-Fi Set Up Using WPS With Windows - PIXMA MX410 Printer

Article ID: ART109249 | Date published: 05/11/2015 | Date last updated: 03/19/2020
 

Description

Learn how to use the WPS (Wi-Fi protected setup) method to set up a PIXMA MX410 to work on a wireless network (LAN).

Solution

If your access point or router supports WPS® (Wi-Fi® Protected Setup), a wireless connection can easily be set up. 

 For details on WPS, refer to the manual of your access point or router.

 


Before you begin

  1. Make sure the computer and access point (router) are connected.
  • (A) Internet
  • (B) Wireless router

 The configuration, router functions, setup procedures and security settings of the network device vary depending on your system environment. For details, refer to your device's instruction manual or contact its manufacturer.

  1. Check to be sure your device supports IEEE802.11n/g/b.
  • In an office setup, consult your network administrator.

 If you connect to a network that's not protected with security measures, there is a risk of disclosing data such as your personal information to a third party.

 If an error message appears, or if you have trouble with the network connection, refer to the printed manual: Network setup troubleshooting.

 An "Ad-hoc connection," which establishes a direct connection to the computer over a wireless connection without using an access point, isn't supported.

 
 

Start WPS setup

 
  1. Use the Menu button (A) to select Device settings.

    Figure: Press the Menu button (A) to select Device settings, then use the Left or Right arrow buttons (B) to select LAN settings, then press OK

  2. Use the left or right arrow   (B) to select LAN settings, then tap OK.

  3. Select WLAN active / inactive, then tap OK.

    Figure: LAN settings, WLAN active/inactive shown on LCD

  4. Select Wireless LAN active, then tap OK.

    Figure: WLAN active/inactive, Wireless LAN active shown on LCD. Wi-Fi lamp (C) is lit

    When wireless connection is enabled, the Wi-Fi lamp (C) lights blue.

    Wi-Fi lamp lit blue

  5. Select Wireless LAN setup, then tap OK.

    Figure: LAN settings, Wireless LAN setup shown on LCD

  6. Select WPS, then tap OK.

    Figure: Wireless LAN setup, WPS shown on LCD

  7. Select Push button method, then tap OK.

    Figure: WPS, Push button method shown on LCD

  8. Press and hold the WPS button on the router (for about 5 seconds), then tap OK on the machine within 2 minutes. For details on the WPS button, refer to the router manual.

    Figure: Message scrolling on LCD, WPS button on wireless router

    The Wi-Fi lamp (blue) on the machine flashes while searching for or connecting to an access point.

    Wi-Fi lamp flashing blue

  9. When this screen appears, tap OK.

    Figure: Connected. Press [OK] shown on LCD

 If the timeout error screen appears, tap OK, then start over from step 8.
  • If another error appears, refer to the printed manual: Network setup troubleshooting.

  • ​To use the PIN code method for setup, select PIN code method in Step 7, then press the OK button. Follow the on-screen instructions to operate the machine and router. When the screen in step 9 appears, press the OK button.

  • If the setup isn't complete within 10 minutes and the timeout error screen appears, press the OK button to perform the setup again and set the new PIN code displayed on the screen to the access point. If another error displays, refer to the printed manual: Network setup troubleshooting.

 


Software Installation

To use the printer with a computer, software and drivers needs to be installed on the computer. The installation process takes about 20 minutes and may require an internet connection.

 Quit all running applications before installation.

  • Log on with administrator rights.

  • If the firewall function of your security software is turned on, a warning message may appear that Canon software is attempting to access the network. If such a warning message appears, set the security software to always allow access.

  1. Make sure that any of the lamps on the mode buttons (A) light and that the Wi-Fi lamp (B) lights blue.

    Make sure that any of the lamps on the mode buttons (A) are lit and that the Wi-Fi lamp (B) is lit blue

  •  If the printer is already connected to the network, you don't need to use a USB cable to perform a network setup.
  1. Turn on the computer, then download the MP Driver from our website. After the file finishes downloading, open it. If you're asked to provide permission to continue, select Yes.

  2. When the setup program begins, select Next.

  3. Select your place of residence, then select Next.

  4. Read the license agreement, then select Yes.

  5. Select Use the printer with wireless LAN connection, then select Next.

    When the Check Printer window appears, select OK. The computer searches for the printer on the network.

  6. Your printer displays in the window. Make sure it's selected, then select Next.

     If your printer isn't detected, check any installed security or firewall software to see if it's blocking any ports that the printer uses for network communication. Refer to your security or firewall software documentation for more information.

  7. When the Setup Completion screen appears, select Complete.

 

If your product issue was not resolved after following the steps above, or if you require additional help, please create or log in to your Canon Account to see your technical support options.
 

SIMS Doc Id

0

Rate this Article
Was this article helpful?
Yes, This document is helpful
No, This document needs a clearer explanation
 
Please provide your comments