Setting the Wireless LAN Manually

Switching the Connection Method to Wireless LAN

1. Press [ ] (Menu).

2. Press [ ] or [ ] to select <Network Settings>, and then press [OK].

The next screen is displayed for approximately 5 seconds.

Turn OFF/ON using Step 5. Turning this OFF/ON is not required.

3. Press [ ] or [ ] to select <Select Wired/Wireless LAN>, and then press [OK].

4. Press [ ] or [ ] to select <Wireless LAN>, and then press [OK].

5. Turns the machine OFF/ON when the following screen disappears.

It is necessary to turn the machine OFF/ON to activate the settings.

Turn OFF the machine and wait for at least 10 seconds before turning it back ON.

Setting by Manually Selecting an Access Point

1. Write down the following information required for the settings.

The information is needed in steps 8 through 10.

* For more information on how to check, refer to the instruction manual of the wireless LAN router or access point, or contact the manufacturer.

SSID

* It may be indicated as access point name or network name.

Write down all if there is multiple SSID.

It is used when selecting an access point in Step 8.

Network key

* It may be indicated as encryption key, WEP key, WPA/WPA2 passphrase, PSK or pre-shared key.

You write down here is the network key that is currently specified for the wireless LAN router or access point.

It is used when entering an network key in Step 10.

• Number of network key characters (digits)

Select the entry format that matches the number of network key characters (digits) in Step 9.

2. Press [ ] (Menu).

3. Press [ ] or [ ] to select <Network Settings>, and then press [OK].

The next screen is displayed for approximately 5 seconds.

You do not need to turn the machine OFF/ON in this step.

4. Press [ ] or [ ] to select <Wireless LAN Settings>, and then press [OK].

5. Press [OK].

6. Press [ ] or [ ] to select <SSID Settings>, and then press [OK].

7. Press [ ] or [ ] to select <Select Access Point>, and then press [OK].

8. Press [ ] or [ ] to select the matched SSID that you have written down in step 1, and then press [OK].

If the multiple matched SSID are displayed, select the one that is displayed at the top (a stronger signal).

The next screen is displayed for approximately 5 seconds.

9. Press [ ] or [ ] to select the entry format that matches the number of network key characters (digits) that you have written down in step 1, and then press [OK].

Either of the following screens is displayed.

10. Enter the network key that you have written down in step 1.

ASCII text

(1) Press [ ] (Tone), and then select <Entry Mode>.

(2) Enter the network key.

You can enter it using the numeric keys.

(3) Select <Apply> using [ ] or [ ], and then press [OK].

Hexadecimal

(1) Enter the network key.

Select the character using [ ] or [ ], and then press [OK] to enter.

(2) Select <Apply> using [ ] or [ ], and then press [OK].

11. Press [ ] to select <Yes>, and then press [OK].

The Wi-Fi indicator blinks.

The next screen is displayed for approximately 2 seconds, and then the Wi-Fi indicator lights.

* If an error message appears, press [OK] to close the screen, check to make sure that the network key is correct, and follow the procedure in 7 again.

12. Wait until the machine sets the IP address automatically (approx. 2 min).

Checking the Wireless LAN Setting is Completed

1. Press [ ] (Status Monitor/Cancel).

2. Select <Network Information> with [ ] and [ ], and then press [OK].

3. Select <IPv4> with [ ] and [ ], and then press [OK].

4. Select <IP Address> with [ ] and [ ], and then press [OK].

5. Take note of the IP address.

6. Press [ ] (Status Monitor/Cancel) to close the screen.

7. Start the web browser of a computer which is connected to a network.

8. Enter http://<IP address of the machine>/ in the address field, and then press the [ENTER] key on your keyboard. The <IP address of the machine> is the address noted in step 5 above.

9. Check that the screen of the Remote UI is displayed.