Loading Paper in the Front Tray

Before loading paper, see Notes on Loading Paper.

Important When loading paper in the Front Tray, the paper sticks out from the back of the printer. Keep a space of 15.7 inches / 40 cm for this purpose behind the printer.   There are wheels on the back corners of the printer. Lift up the front of the printer to move it back and forth.

Note You can load A3+ (13" x 19"), A3, B4, A4, B5, A5, Letter, Legal, 11" x 17" / 279.4 x 431.8 mm (Tabloid), Wide (4" x 7.1"), 4" x 6" / 10 x 15 cm, 4" x 8" / 101.6 x 203.2 mm, 5" x 7" / 13 x 18 cm, 8" x 10" / 20 x 25 cm, 10" x 12" / 25 x 30 cm, and 14" x 17" / 36 x 43 cm sizes of paper in the Front Tray.   When printing on paper other than 14" x 17" / 36 x 43 cm size from a PictBridge compliant device, load paper in the Rear Tray.

1. Set the Front Tray in the front paper feeding position.
   
   (1) Gently press the upper center of the Front Tray to open it.
   
   
   
   (2) Tilt the Front Tray upward.
   
   
   
   (3) Lift the Front Tray until it stops.
   The Front Feed button lights.
   
   
   
   (4) While keeping the Front Tray lifted, tilt the Front Tray forward to set it in the front paper feeding position.
   
   (5) Make sure that the Front Feed button is lit.
   
   
    

2. Press the Front Feed Support button to open the Front Feed Support.
   
   
    

3. Prepare for loading paper.
   
   (1) Pull out the Front Tray Extension.
   
   (2) Press the right corner of the Front Feed Support to open the V-shaped Support.
   
    Note

• When loading A4 or smaller size paper, this procedure is not necessary.
   

(3) Press the Front Feed button.

The printer starts making operating noise, then the Power lamp flashes for about 30 seconds.

 Important

• Do not load paper when the Power lamp is flashing. Otherwise, the paper or the printer may be damaged.

 

4. Load paper.
   
   (1) Make sure that the Power lamp is lit and the Front Feed button is flashing quickly.
   If the Power lamp is flashing, wait until it stops flashing and stays lit.
   
   (2) Load the paper straight into the Front Tray WITH THE PRINT SIDE FACING UP.
   Align the front edge of the paper with the mark  (Paper Alignment Mark) on the Front Tray.
   Load only one sheet of paper in the Front Tray at a time.
    

 Note

• Align the right edge of the paper with the right side (A) of the Front Tray and load the paper straight into the Front Tray.
   
• If paper is curled, hold the curled corners and gently bend them in the opposite direction until the paper becomes completely flat.
   
• When using Photo Paper Plus Semi-gloss, even if the sheet is curled, load one sheet at a time as it is. If you roll up this paper to flatten, this may cause cracks on the surface of the paper and reduce the print quality.

 Important

• If the printer is not used for about 5 minutes while it is as described in (1) in step 4 above, the Front Feed button stops flashing and stays lit, and you cannot load the paper in the Front Tray. In this case, return to (3) in step 3.
   

5. Press the Front Feed button to feed the paper from the Front Tray.
   The paper feeds into the printer automatically and the Front Feed button flashes slowly.
   The printer is ready to start printing.
   
   
   
    Note
   
   After loading paper

• Select the size and type of the loaded paper in Printer Paper Size (or Paper Size) and Media Type in the printer driver.
   

To print continuously

• To print from the Front Tray again, return to (3) in step 3 and load paper in the Front Tray. Then start printing.

Returning the Front Tray to Its Normal Printing Position

When using the Rear Tray, set the Front Tray to its normal printing position.

 Important

• Be sure to follow the procedure below when returning the Front Tray to its normal printing position. Otherwise, the printer may be damaged.
   
• When the Front Tray is set to the front paper feeding position, printing by using the Rear Tray is not possible. Be sure to set it to its normal printing position.

1. Hold the Front Tray and slowly tilt it like you are closing it.
   Tilting the Front Tray lowers it to its normal printing position.Hold the Front Tray and slowly tilt it like you are closing it.
   
   
    

2. Open the Front Tray.
   
   (1) Open the Front Tray to return it to its normal printing position.
   
   (2) Make sure that the Front Feed button is not lit.