Printing Out Network Setting Information - iP110

Article ID: ART116581 | Date published: 05/12/2015 | Date last updated: 05/10/2019
 

Description

This article explains how to print a Network Configuration Page (also known as a LAN Details Page).  An example of this page is attached to this article.

Solution

Note

  • The steps listed below are specific to the iP110.  For instructions for other models, click here


You can print out the current network settings of the printer.


Important

  • This print out contains valuable information about your computer. Handle it with care.​
 
  1. Make sure that the printer is turned on.

  2. Load a sheet of A4 or Letter-sized plain paper.

  3. Press and hold the RESUME/CANCEL button, then release the button when the POWER lamp flashes 6 times.

    The printer starts printing the network setting information.

    The following information on the printer's network setting is printed out.

    Item

    Explanations of the item

    Setting

    Wireless LAN

    Wireless LAN

    Enable/Disable

    Connection

    Connection status

    Active/Inactive

    MAC Address

    MAC Address

    XX:XX:XX:XX:XX:XX

    SSID

    SSID

    SSID of the wireless LAN/SSID of the access point mode

    Password

    Password

    Password of the access point mode (8 to 10 alphanumeric characters)

    Communication Mode

    Communication Mode

    Infrastructure/Access Point Mode

    Channel *1

    Channel

    XX (1 to 13)

    Encryption

    Method of the Encryption

    none/WEP/TKIP/AES

    WEP Key Length

    WEP Key Length

    Inactive/128/64

    Authentication

    Method of the Authentication

    none/auto/open/shared/WPA-PSK/WPA2-PSK

    Signal Strength

    Signal Strength

    0 to 100 [%]

    TCP/IP Version

    TCP/IP Version

    IPv4 & IPv6/IPv4

    IPv4 IP Address

    Selected IP Address (IPv4)

    XXX.XXX.XXX.XXX

    IPv4 Default Gateway

    Default Gateway (IPv4)

    XXX.XXX.XXX.XXX

    Subnet Mask

    Subnet Mask

    XXX.XXX.XXX.XXX

    IPv6 IP Address *2

    Selected IP Address (IPv6)

    XXXX:XXXX:XXXX:XXXX
    XXXX:XXXX:XXXX:XXXX

    IPv6 Default Gateway *2

    Default Gateway (IPv6)

    XXXX:XXXX:XXXX:XXXX
    XXXX:XXXX:XXXX:XXXX

    Subnet Prefix Length *2

    Subnet Prefix Length

    XXX

    IPsec *3

    IPsec setting

    Active

    Security Protocol *3

    Method of the Security Protocol

    ESP/ESP & AH/AH

    WPS PIN CODE

    WPS PIN code

    XXXXXXXX

    Wireless LAN DRX

    Discontinuous reception (wireless LAN)

    Enable/Disable

    Other Settings

    Other settings

    -

    Printer Name

    Printer name

    Printer name (Up to 15 alphanumeric characters)

    WSD

    WSD setting

    Enable/Disable

    WSD Timeout

    Timeout

    1/5/10/15/20 [min]

    LPR Protocol

    LPR protocol setting

    Enable/Disable

    Bonjour

    Bonjour setting

    Enable/Disable

    Bonjour Service Name

    Bonjour service name

    Bonjour service name (Up to 52 alphanumeric characters)

    PictBridge Commun.

    PictBridge Communication

    Enable/Disable

    DNS Server

    Getting DNS Server automatically

    Auto/Manual

    Primary Server

    Primary server address

    XXX.XXX.XXX.XXX

    Secondary Server

    Secondary server address

    XXX.XXX.XXX.XXX

    Proxy Server

    Proxy Server setting

    Enable/Disable

    Proxy Port

    Specifying Proxy Port

    1 to 65535

    Proxy Address

    Proxy Address

    XXXXXXXXXXXXXXXXXXXX

    ("XX" represents alphanumeric characters.)

    *1 Depending on the country or region of purchase, one of the channels from 1 to 11 is printed.

    *2 Only when IPv6 is enabled, the status of the network is printed.

    *3 Only when IPv6 and the IPsec setting are enabled, the status of the network is printed.


 

Attachment

iP110_NW_Settings.pdf
76K • < 1 minute @ 56k, < 1 minute @ broadband



Rate this Article
Was this article helpful?
Yes, This document is helpful
No, This document needs a clearer explanation
 
Please provide your comments