Images are blurry or not in focus (PowerShot G15 / SX50 HS)

Article ID: ART136808 | Date published: 05/13/2015 | Date last updated: 02/16/2016


Images are blurry or not in focus (PowerShot G15 / SX50 HS)



The position and shape of the operation buttons, screens displayed, and setting items may differ according to the model you use.



When an image is blurry or cannot be brought into focus during shooting, please check the following.


1. Holding the Camera

You can prevent camera shake by holding the camera firmly.
Keep your arms tight against your body while holding the camera firmly by the sides. Be sure that your fingers do not block the <flash>.


2. When the Camera Shake Icon Appears

When you press the <Shutter Button> halfway in low light conditions where camera shake is likely, a flashing () will appear.



  • Set the [IS mode] to [Continuous].
Press <> button > [Shooting] tab () > [IS Settings], and then select [Continuous] for the [IS Mode].



  • Set the flash to [On] ()
If using the PowerShot G15:
After moving the <> switch and pressing the <flash> button (), press the right <directional button> a few times to set to [On] ().
If using the PowerShot SX50 HS:
After raising the flash with your finger and pressing the <flash> button(), press the right <directional button> a few times to set to [On] ().



  • Increase the [ISO speed].
Operate the <ISO> button () and <directional button> to set the desired [ISO speed].


For details on the setting screen that appears on your camera or the [Shooting Modes] in which the [ISO Speed] can be set, see the table at the end of the page.


  • Attach the camera to a tripod.
Additionally, you should set the [IS Mode] to [Off] when shooting with a tripod.


3. Image is blurred

  • Press the <Shutter Button> halfway to focus on the subject, then press fully to shoot.
Half-press the <Shutter Button> (press lightly to focus), and then press it fully (without releasing the <Shutter Button>, press it all the way down).



  • Shoot the subject within the focusing distance.
For details on the shooting distances for the [Focusing Range] of your camera, please see the table at the end of the page.



  • Set the [AF-assist Beam] to [On].
Press the <
> button, select the [Shooting] tab (
), and then set the [AF-assist Beam] to [On].



  • Confirm that functions which you do not intend to use (macro, etc.) are not set.
Press the <Macro> button () several times to select a suitable [Focusing Range].



  • Shoot using the focus lock or AF lock
- Focus Lock
Change the composition while holding the <Shutter Button> down halfway.



- AF Lock
Keep the <Shutter Button> pressed halfway and press the left <directional button>.

The focus locks, and () and [MF indicator] appear on the screen.


4. The AF frame does not appear, and the camera does not focus

If you center on the light and dark contrasting area of the subject and push the <Shutter Button> halfway, or repeatedly push the <Shutter Button> halfway, the [AF frame] will appear and the camera will focus.

The camera may not be able to focus in some conditions.


5. Information on different models

... Available or set automatically.

... Not available.
* ... PowerShot SX50 HS
Model ISO Speed Shooting modes in which the ISO speed setting can be made


PowerShot G15 / PowerShot SX50 HS


Model Focusing zone
Figures in the upper line: [Normal] (

Figures in the bottom line : [Macro] (
PowerShot G15 [Normal] 5 cm (2.0 in.) - infinity (W)* /40 cm (1.3 ft.) - infinity (T)**
[Macro] 1 cm - 50 cm (0.4 in. - 1.6 ft.) (W)*
PowerShot SX50 HS [Normal] 5 cm (2.0 in.) - infinity (W)* /1.3 m (4.3 ft.) - infinity (T)**
[Macro] 0 - 50 cm (0 - 1.6 ft.) (W)*
* (W): When turning the toward ( ) to the maximum wide angle side (Max. wide angle).
** (T): When turning the toward (
) to the maximum telephoto side (Max. telephoto).




Rate this Article
Was this article helpful?
Yes, This document is helpful
No, This document needs a clearer explanation
Please provide your comments