The Flash does not Fire during Wireless Flash Shooting
Article ID: ART143779 | Date published: 05/13/2015 | Date last updated: 09/11/2018
 

Description

The Flash does not Fire during Wireless Flash Shooting

Solution

 

Failure of receiver flash units to fire when using wireless flash for shooting may be caused by the following problems.
  • Receiver units are set to a different transmission channel than the sender unit.
  • Receiver units are not placed properly.
In these cases, refer to the following information to check flash unit settings and placement.
REFERENCE
  • In this explanation [sender] refers to the camera flash unit, and [receiver] refers to controlled wireless flash units.
  • The EOS REBEL T5i / EOS 700Ds flash (sender) and Speedlite 430EX (receiver) have been used for the purposes of explanation.
  • Use the mini stand (tripod socket provided) to prop up the receiver unit.
  • The position and shape of the operation buttons, and setting items may differ according to the model you use.
  • For more detailed information on wireless flash photography, or control settings for the sender flash unit, refer to the camera/flash instruction manual.
NOTE
Icons used on this page:
Flash
<ZOOM/>: Wireless setting button / <>: +/- button / <>: Select/Setting button
Camera
<><>: Cross keys / [ ]: Shooting tab 1 / <>: Setting button / <>: Flash button

 

Select a Transmission Channel

1. Camera (sender) unit set-up.
Set the camera's power switch to <ON>.

 

 

2. Press the <> button to raise the built-in flash.
For wireless flash shooting, be sure to raise the built-in flash.

 

 

3. Press the <MENU> button and then use the <>keys to select [Flash Control] under the [ ] tab. Then, press <>.

 

 

4. Press the <> keys to select [Built-in flash settings], then press <>.

 

 

5. Press the <> keys to select [Built-in flash], then press <>.

 

 

 

6. Press the <> keys to select [EasyWireless], then press <>.

 

 

7. Press the <> keys to select [Channel], then press <>.

 

 

8. Select the transmission channel (1-4), then press <>.

 

 

9. External flash (receiver) unit set-up.
Set the External flash units power switch to <ON>.

 

 

10. Press the <ZOOM /> button for 2 seconds. [receiver] will light up, and the external flash will be set to receiver mode.

 

 

11. Press the <ZOOM /> button until [CH] begins to blink.

 

 

12. Press the <> button to set the receiver unit to the same transmission channel as the sender unit, and then press <>.

 

 

This concludes the channel settings.

 

 

Position The receiver Unit(s) within Range of the sender Unit.

Position the camera and receiver unit(s) within the range shown below.

REFERENCE
  • If there is a test firing setting on the sender, press the sender units test firing button to test-fire the receiver unit. If the receiver unit does not fire, adjust its angle toward the sender unit and distance from the sender unit.
  • The above image shows the effective transmission range when the EOS REBEL T5i / EOS 700Ds built-in flash is used for wireless flash photography. The effective transmission range and angle may differ depending on the camera/flash you used as the sender unit. For more information, refer to the manual that came with your camera or flash unit.

 

 

Aim the receiver Units Receiver at the sender Unit.

Use the bounce feature to swing the receiver units flash body so that the wireless sensor faces the sender unit.

 

 

  • Indoors, the wireless signal can also bounce off the wall so there is more leeway in positioning the receiver unit(s).
  • After positioning the receiver unit(s), be sure to test the wireless flash operation before shooting.
  • Do not place any obstacles between the sender unit and receiver unit(s). Obstacles can block the transmission of wireless signals.
REFERENCE
  • If there is a test firing setting on the sender, press the sender units test firing button to test-fire the receiver unit. If the receiver unit does not fire, adjust its angle toward the sender unit and distance from the sender unit.

 

Wireless Flash Shooting

The following section provides an overview of the basic and easy full-automatic wireless flash shooting mode.
CAUTION
  • To avoid overheating and degrading the flash head, do not fire more than 20 continuous flashes. After 20 continuous flashes, allow a rest time of at least 10 min.
  • If you fire more than 20 continuous flashes and then fire more flashes in short intervals, the inner overheating prevention function may be activated to make the recycling time about 8 to 20 sec. If this occurs, allow a rest time of about 15 min. and the flash will then return to normal.
  • The above information on number of continuous flashes and rest times is for the Speedlite 430EX II. Depending on the flash, the number of continuous flashes and rest time may differ. Make sure to read the manuals that came with your camera and flash carefully.

 

 

1. Set the powers switches of the flash and camera to <ON>.


 

 

2. Press the <MENU> button and then use the <>keys to select [Flash Control] under the [ ] tab, and then press <>.

 

 

3. Press the <> keys to select [E-TTL II meter.], then press <>.

 

 

4. Press the <> keys to select [Evaluative], then press <>.

 

 

5. Press the <> keys to select [Built-in flash settings], then press <>.

 

 

6. Press the <> keys to select [Built-in flash], then press <>.

 

 

7. Press the <> keys to select [EasyWireless], then press <>.

REFERENCE
  • Even though the firing of the built-in flash is disabled when [EasyWireless] is set, it will still fire a small flash to control the receiver unit. Depending on shooting conditions, the flash fired to control the receiver unit may appear in the picture.

 

 

8. Set [Channel] for the sender and receiver units.
For more information, refer to step 6 of Select a Transmission Channel.

 

 

9. Position the receiver unit(s) within the sender units wireless transmission range.
For more information, refer to Position the receiver Unit(s) within Range of the sender Unit.
Aim the receiver Units Receiver at the sender Unit.

 

 

10. Check that the flash is ready.
When the receiver unit(s) is ready to fire (fully charged), the AF-assist beam will blink at 1-sec. intervals.

 

 

11. Set the camera in the same way as with normal flash shooting.

 

 

12. To exit wireless flash shooting, select [NormalFiring] for [Built-in flash].

 

SIMS Doc Id

8201802600