List of messages that appear on ZR65mc and ZR70mc
Memory Card Related Messages
Direct Print Related Messages
|
Message
|
Explanation
|
| SET THE TIME ZONE, DATE AND TIME |
You have not set the time zone, date and time. This message appears each time you turn the power on until you set the time zone, date and time. |
| CHANGE THE BATTERY PACK |
Battery pack is exhausted. Replace or charge the battery pack. |
| THE TAPE IS SET FOR ERASURE PREVENTION |
Cassette is protected. Replace the cassette or change the position of the protect switch. |
| REMOVE THE CASSETTE |
Camcorder stopped operating to protect the tape. Unload and reload the cassette. |
| CHECK THE DV INPUT |
DV cable is not connected, or the connected digital device is turned off. |
| CONDENSATION HAS BEEN DETECTED |
Condensation has been detected in the camcorder. |
| TAPE END |
Tape reached the end. Rewind the tape or replace the cassette. |
| CHECK THE CASSETTE [REC MODE] |
You attempted to perform audio dubbing on a tape recorded in a mode other than the SP mode. |
| CHECK THE CASSETTE [AUDIO MODE] |
You attempted to perform audio dubbing on a tape recorded in 16-bit or 12-bit 4-channel sound. |
| CHECK THE CASSETTE [BLANK] |
You attempted to perform audio dubbing on a tape with a blank section. |
| COPYRIGHT PROTECTED PLAYBACK IS RESTRICTED |
You attempted to play back a copyright protected tape. |
| COPYRIGHT PROTECTED DUBBING RESTRICTED |
You attempted to dub a copyright protected tape. May also appear when an anomalous signal is received during analog line-in recording, or during analog-digital conversion of a copyright protected tape. |
Memory Card Related Messages
|
Message
|
Explanation
|
| NO CARD |
Memory card not is inserted into the camcorder. |
| THE CARD IS SET FOR ERASURE PREVENTION |
SD Memory Card is set for erasure prevention. Replace the card or change the position of the protect switch. |
| NO IMAGES |
No images are recorded on the memory card. |
| CARD ERROR |
A memory card error occurred. The camcorder cannot record or play back the image. The error may be temporary. If the message disappears after 4 seconds and " " flashes red, turn the camcorder off, remove the card and reinsert the card. If "" changes to green, you can continue recording/playback. |
| CARD FULL |
No remaining capacity on the memory card. Replace with another card or erase images. |
| NAMING ERROR |
File or folder number has reached the maximum value. |
| UNIDENTIFIABLE IMAGE |
Image is not recorded with JPEG compression, or with a compression not compatible with the camcorder, or the image file is corrupted. |
| PRINT ORDER ERROR |
You attempted to set more than 200 transfer orders. |
| THIS IMAGE CANNOT BE RECORDED |
Some analog images cannot be recorded on the memory card depending on the signal. |
Direct Print Related Messages
Following messages may appear on the camcorder screen. On printers equipped with an operation panel, an error number or message displays on the panel. Refer to the printer manual for the remedies corresponding to the error numbers or messages.
|
Message
|
Explanation
|
| NO PAPER |
Paper cassette is not correctly inserted or is out of paper. |
| PAPER JAM |
The paper jammed during printing. |
| MEDIA TYPE ERROR |
Wrong paper. Cancel printing and set the paper you chose in the print settings menu. |
| NO INK |
The ink cartridge is not inserted or is out of ink. |
| LOW INK LEVEL |
The ink tank needs to be replaced soon. Prepare a new ink tank. If you select [Continue] in the error screen, you can restart printing. |
| WASTE TANK FULL |
Waste tank is full. You can restart printing by pressing the RESUME/CANCEL button on the Bubble Jet Printer. Request replacement of the waste tank at the shop where you purchased the printer or the nearest Canon customer support center listed in the Bubble Jet Quick Start Guide. |
| CANNOT PRINT! |
You attempted to print an image that was recorded with another camcorder, with a different compression, or was edited on a computer. |
| COULD NOT PRINT X IMAGES |
You attempted to use the print order settings to print X images that were recorded with another camcorder, with a different compression or were edited on a computer. |
| SET PRINT ORDER |
You attempted to print an image from the CARD PLAY menu [ PRINT] without having set the print order. |
| PRINTER ERROR |
Cancel printing. Turn off the printer and turn it back on. Check the printer status. |
| COMMUNICATION ERROR |
The printer is experiencing a data transmission error. Cancel printing, disconnect the USB cable and turn off the printer. After a while, turn the printer back on and reconnect the USB cable. Or, you attempted to print from a memory card that contains a large number of images. Reduce the number of images. |
| PRINTER IN USE |
The printer is printing from a computer or a memory card inserted into the printer. It automatically starts printing from the camcorder when current prints are complete. |
| PRINTER WARMING UP |
Printer is warming up. If the message does not disappear after a few seconds, check the printer status. |
| PAPER LEVER ERROR |
Paper lever error occurred. Adjust the paper selection lever to the proper position. |
| PRINTER COVER OPEN |
Printer cover is open. Close the printer cover securely. |
| NO PRINTHEAD |
No print head is installed in the printer or print head is defective. Refer to the instruction manual of your printer. |
