Installation Procedure

Select an appropriate installation site. Then, follow the procedure described below to install the copier.

Do not insert the copier plug, press the power switch or turn the power ON before completing steps 2 to 7. If you do, you could damage your copier.

1. Remove the copier from the shipping bag. Then, peel off all packing tape attached to the copier.
   
   
   If the copier is brought from the cold outdoors into a warm room, condensation may form and result in an inability to obtain normal copy images. Under such conditions, allow at least two hours for the copier to adjust to room temperature before attempting to use it.
   
   
   
   
2. Remove shipping attachment (1) on the left side of the main unit. (In step 7, insert the shipping attachment (1) in the shipping attachment holder.)
   
   
   Remove shipping attachment (2) on the right side of the main unit. (In step 7, insert shipping attachment (2) in the shipping attachment holder.)
   
   
   
   
   • You will need these shipping attachments whenever you transport the copier, so store them in the shipping attachment holder.
   • The edge of a coin will allow for easy removal.
     
     
     
3. Remove the protective sheet from the platen glass.
   
   
   
   
4. Lift the main unit lever on the left side of the main unit and open the main unit.
   
   
   
   
5. Remove the protective sheet from the output slot.
   
   
   
   
6. Squeeze and remove the attachment inside the copier under the top of the main unit.
   
   
   
   
7. Insert shipping attachment (1) and (2) in the shipping attachment holder, removed in step 2.
   
   
   
   
8. Grip the end of the cartridge, and pull it out of the copier.
   
   
   
   Although the cartridge comes already installed in the main unit, you cannot make copies until after you have completed the following steps.
   
   
   
9. Hold the cartridge level so that the side with the written instructions is facing upward. Rock the cartridge several times at a 90^o angle to evenly distribute the toner in the cartridge.
   
   
   
   
10. Place the cartridge on a flat, level surface (e.g., a desk or table). Peel the sealing tape grip from the end of the cartridge. Grasps the grip and pull the sealing tape out in the direction of the arrow mark away from the cartridge.
    
    
    
    • When removing the sealing tape, take care not to allow the toner on the sealing tape to come in contact with your hands or clothing. If you get toner on either your hands or clothing, wash immediately with cold water. Washing with warm water will set the toner and make it impossible to remove.
    • Do not pull the sealing tape at an angle. If the sealing tape breaks before being pulled out fully, you will not be able to use the cartridge.
    • Do not press down on the cartridge.
    
    
    • The sealing tape grip is affixed to the end of the cartridge. Before pulling out the tape, be sure to peel it from the end of the cartridge. Then, pull the tape out slowly from the cartridge.
    • The sealing tape is approximately 20" (50 cm) long. Be sure to pull the sealing tape completely out of the cartridge.
    
    
11. Hold the cartridge so that the side with the written instructions is facing upward. Then, carefully insert the cartridge into the copier as far as it will go.
    
    
    
    Insert the cartridge so that the arrow on the side with the written instructions is pointing away from you.
    
    
    
12. Close the main unit by pressing down firmly on the part marked "".
    
    
    
    When you close the main unit, be careful not to get your hand in the way.
    
    
    
13. Plug one end of the power cord into the copier power inlet.
    
    
    
    
14. Plug the other end of the power cord into an outlet.
    
    
    
    This copier is designed for use with a power source matching the power requirements shown on the marking label on the back of the copier. If you are unsure of the power source, check with your local power company.
    
    
    
15. Insert the copy tray so that it fits into the three holes located on the side of the copier.
    
    
    
    Make sure that the copy tray is inserted into the copier as far as it will go.
    
    
    
16. Remove the packing material inside the cassette and load copy paper into the cassette.
    
    
    
    
17. The instruction label on the cassette is written only in English. If you prefer to use a French, German, Spanish, or Italian label, affix the appropriate label over the English one as shown in the illustration. Push the cassette back into the copier.