List of messages and their explanations that appear on Elura 80, Elura 85, and Elura 90, Elura 100
Article ID: ART157093 | Date published: 06/09/2015 | Date last updated: 08/17/2015
 

Description

List of messages that appear on Elura 80, Elura 85, and Elura 90 Elura 100(and their explanations)

Solution

List of messages that appear on Elura 80, Elura 85, and Elura 90


Memory Card Related Messages

Direct Print Related Messages

Message

Explanation

SET THE TIME ZONE, DATE AND TIME You have not set the time zone, date and time. This message appears each time you turn the power on until you set the time zone, date and time.
CHANGE THE BATTERY PACK Battery pack is exhausted. Replace or charge the battery pack.
THE TAPE IS SET FOR ERASURE PREVENTION Cassette is protected. Replace the cassette or change the position of the protect switch.
REMOVE THE CASSETTE Camcorder stopped operating to protect the tape. Unload and reload the cassette.
CHECK THE INPUT DV cable or USB cable is not connected, or the connected digital device is turned off.
CONDENSATION HAS BEEN DETECTED Condensation has been detected in the camcorder.
TAPE END Tape reached the end. Rewind the tape or replace the cassette.
CHECK THE CASSETTE [REC MODE] You attempted to perform audio dubbing on a tape recorded in a mode other than the SP mode.
CHECK THE CASSETTE [AUDIO MODE] You attempted to perform audio dubbing on a tape recorded in 16-bit or 12-bit 4-channel sound.
CHECK THE CASSETTE [BLANK] You attempted to perform audio dubbing on a tape with a blank section.
WRONG FORMAT PLAYBACK NOT POSSIBLE You attempted to play back a tape recorded in HD format.
CHECK THE CASSETTE [WRONG FORMAT] You attempted to perform audio dubbing on a tape recorded in HD format.
HEADS DIRTY, USE CLEANING CASSETTE Video heads are dirty. Clean the video heads.
COPYRIGHT PROTECTED PLAYBACK IS RESTRICTED You attempted to play back a copyright protected tape.
COPYRIGHT PROTECTED DUBBING RESTRICTED You attempted to dub a copyright protected tape. May also appear when an anomalous signal is received during analog line-in recording, or during analog-digital conversion of a copyright protected tape.

Memory Card Related Messages

Message

Explanation

NO CARD Memory card not is inserted into the camcorder.
THE CARD IS SET FOR ERASURE PREVENTION SD Memory Card is set for erasure prevention. Replace the card or change the position of the protect switch.
NO IMAGES No images are recorded on the memory card.
CARD ERROR A memory card error occurred. The camcorder cannot record or play back the image. The error may be temporary. If the message disappears after 4 seconds and "" flashes red, turn the camcorder off, remove the card and reinsert the card. If "" changes to green, you can continue recording/playback.
CARD FULL No remaining capacity on the memory card. Replace with another card or erase images.
NAMING ERROR File or folder number has reached the maximum value.
UNIDENTIFIABLE IMAGE Image is not recorded with JPEG compression, or with a compression not compatible with the camcorder, or the image file is corrupted.
  TRANSFER ORDER ERROR You attempted to set more than 200 transfer orders.
CANNOT TRANSFER! You attempted to transfer a movie file as wallpaper.
THIS IMAGE CANNOT BE RECORDED Some analog images cannot be recorded on the memory card depending on the signal.
THIS IMAGE CANNOT BE USED AS START-UP IMAGE You attempted to use an image recorded with another camcorder, recorded with a compression not compatible with this camcorder, or that has been edited on a computer.
TOO MANY STILL IMAGES DISCONNECT USB CABLE Disconnect the USB cable and decrease the number of still images on the memory card to less than 1800. If a dialog appeared on the computer screen, close it. Reconnect the USB cable.

Direct Print Related Messages

Following messages may appear on the camcorder screen. On printers equipped with an operation panel or printer that can be connected to a TV, an error number or message displays on the panel or TV monitor. Refer to the printer manual for the remedies corresponding to the error numbers or messages.

Message

Explanation

PAPER ERROR There is a problem with the paper. Wrong paper size is inserted, the ink cannot be used with the selected paper or paper output tray is open.
NO PAPER Paper is not correctly inserted or there is no paper. If the printer is equipped with a photo paper cassette, specify the paper feed location using the Paper Feed switch.
PAPER JAM The paper jammed during printing. Select [STOP] to cancel printing. After removing the paper, set some paper again and press the resume button on the printer.
PAPER HAS BEEN CHANGED Paper size has been changed between print setting and start of printing.
MEDIA TYPE ERROR You attempted to use a paper size/type that is not supported by the printer.
INCOMPATIBLE PAPER SIZE You attempted to print on paper that cannot be used with the camcorder.
INK ERROR There is a problem with the ink.
NO INK The ink cartridge is not inserted or is out of ink.
LOW INK LEVEL The ink cartridge needs to be replaced soon.
INK CASSETTE ERROR There is a problem with the ink cassette.
PAPER AND INK DO NOT MATCH The ink cannot be used with the selected paper type.
WASTE TANK FULL Waste tank is full. Select [CONTINUE] to restart printing. Consult your dealer or a Canon Service Center listed in the Contact List provided with the printer or the printer manual to replace the waste tank (waste ink absorber).
FILE ERROR You attempted to print an image that was recorded with another camcorder, with a different compression, or was edited on a computer.
CANNOT  PRINT! You attempted to print an image that was recorded with another camcorder, with a different compression, or was edited on a computer.
COULD NOT PRINT X IMAGES You attempted to use the print order settings to print X images that were recorded with another camcorder, with a different compression or were edited on a computer.
SET PRINT ORDER You attempted to print an image from the CARD PLAY menu [    PRINT] without having set the print order.
  PRINT ORDER ERROR You attempted to set more than 200 still images in the print order.
CANNOT TRIM You attempted to trim an image that was recorded with another camcorder.
READJUST TRIMMING You changed the print style after you set the trimming settings.
PRINTER  ERROR Cancel printing. Turn off the printer and turn it back on. Check the printer status. If the error persists, consult your dealer or a Canon Service Center listed in the Contact List provided with the printer or the printer manual.
PRINT ERROR Cancel printing, disconnect the USB cable and turn off the printer. After a while, turn the printer back on and reconnect the USB cable. Check the printer status. If the error persists, consult your dealer or a Canon Service Center listed in the Contact List provided with the printer or the printer manual. When you are printing using the button, check the print settings.
HARDWARE ERROR Cancel printing. Turn off the printer and turn it back on. Check the printer status. If the printer is equipped with a battery, it might be exhausted. In such case, turn off the printer, replace the battery and turn it back on. If the error persists, consult your dealer or a Canon Service Center listed in the Contact List provided with the printer or the printer manual.
RECHARGE THE PRINTER BATTERY The printer battery is depleted.
COMMUNICATION ERROR The printer is experiencing a data transmission error. Cancel printing, disconnect the USB cable and turn off the printer. After a while, turn the printer back on and reconnect the USB cable. When you are printing using the button, check the print settings. Or, you attempted to print from a memory card that contains a large number of images. Reduce the number of images.
CHECK PRINT SETTINGS The print setting cannot be used for printing with the button.
PRINTER IN USE The printer is in use. Check the printer status.
PRINTER WARMING UP Printer is warming up. If the message does not disappear after a few seconds, check the printer status.
PAPER LEVER ERROR Paper lever error occurred. Adjust the paper selection lever to the proper position.
PRINTER COVER OPEN Close the printer cover securely.
NO PRINTHEAD No print head is installed in the printer or print head is defect. Refer to the instruction manual of your printer.

SIMS Doc Id

0