Note: The steps listed below are specific to the MG5420.  For instructions for other models, click here

You can print out the network settings of the machine such as its IP address and SSID.

Important

• This print out contains valuable information about your computer. Handle it with care.

  1. Make sure that the machine is turned on.

  2. Load a sheet of A4 or Letter-sized plain paper.

  3. Select Setup on the HOME screen.

     The menu screen is displayed.

  4. Select Device settings, then use the OK button to confirm the selection.

  5. Use the button to select LAN settings, then use the OK button to confirm the selection.

  6. Use the button to select Confirm LAN settings, then use the OK button to confirm the selection.

  7. Use the button to select Print LAN details, then use the OK button to confirm the selection.

  8. Use the button to select Yes, then use the OK button to start printing.

     The machine starts printing the network setting information.

     The following information on the machine's network setting is printed out.

     Item	Explanations of the item	Setting
     Wireless LAN	Wireless LAN	Enable/Disable
     Connection	Status of the Wireless LAN	Active/Inactive
     MAC Address	MAC Address	XX:XX:XX:XX:XX:XX
     SSID	SSID	SSID of the wireless LAN
     Communication Mode	Communication Mode	Infrastructure
     Channel	Channel	XX (1 to 13)
     Encryption	Method of the Encryption	none/WEP/TKIP/AES
     WEP Key Length	WEP Key Length	Inactive/128/64
     Authentication	Method of the Authentication	none/auto/open/shared/WPA-PSK/WPA2-PSK
     Signal Strength	Signal Strength	0 to 100 [%]
     TCP/IP Version	TCP/IP Version	IPv4 & IPv6/IPv4
     IPv4 IP Address	Selected IP Address (IPv4)	XXX.XXX.XXX.XXX
     IPv4 Default Gateway	Default Gateway (IPv4)	XXX.XXX.XXX.XXX
     Subnet Mask	Subnet Mask	XXX.XXX.XXX.XXX
     IPv6 IP Address *1	Selected IP Address (IPv6)	XXXX:XXXX:XXXX:XXXX XXXX:XXXX:XXXX:XXXX
     IPv6 Default Gateway *1	Default Gateway (IPv6)	XXXX:XXXX:XXXX:XXXX XXXX:XXXX:XXXX:XXXX
     Subnet Prefix Length*1	Subnet Prefix Length	XXX
     IPsec*2	IPsec setting	Active
     Security Protocol*2	Method of the Security Protocol	ESP/ESP & AH/AH
     Wireless LAN DRX	Discontinuous reception (wireless LAN)	Enable/Disable
     Other Settings	Other settings	-
     Printer Name	Printer name	Printer name (Up to 15 characters)
     Shared Memory Card	Memory card sharing	Enable/Disable
     WSD	WSD setting	Enable/Disable
     WSD Timeout	Timeout	1/5/10/15/20 [min]
     LPR Protocol	LPR protocol setting	Enable/Disable
     Bonjour	Bonjour setting	Enable/Disable
     Bonjour Service Name	Bonjour service name	Bonjour service name (Up to 52 characters)
     PictBridge Commun.	PictBridge Communication	Enable/Disable
     DNS Server	Getting DNS Server automatically	Auto/Manual
     Primary Server	Primary server address	XXX.XXX.XXX.XXX
     Secondary Server	Secondary server address	XXX.XXX.XXX.XXX
     Proxy Server	Proxy Server setting	Enable/Disable
     Proxy Port	Specifying Proxy Port	1 to 65535
     Proxy Address	Proxy Address	XXXXXXXXXXXXXXXXXXXX
     IP Address Filtering	IP Address Filtering	Enable/Disable

     ("XX" represents alphanumeric characters.)

     *1 Only when IPv6 is activated, the status of the network is printed.

     *2 Only IPv6 and the IPsec setting are activated, the status of the network is printed.