This product automatically cuts the print media when printing is finished. (Full cut) In addition, a half cut is made between the tubes and labels after printing, so that you can cut the tubes by hand or cleanly peel off labels from release paper.
Change the Half Cut Settings
The default setting is "(Half Cut) On."
If you do not want to use a half cut, you can print the cut line (solid/dotted line).
Half cut |
Cut line settings |
Details |
Print Preview |
On
(Default Setting) |
- |
After printing, cut lines are added between tubes and labels. |
|
Off |
Off |
No cut between tubes or labels after printing, and no cut line will be printed. |
|
Line |
A solid cut line will be printed between tubes and labels after printing. |
|
Dotted |
A dotted cut line will be printed between the printed tubes and labels. |
|
[Example] Printing a cut line (Dotted) without a half cut.
- Press the [Option] key.
|
- Use []
or []
to select "Print Settings" and press the [Enter] key.
|
|
- Use []
or []
to select "Half cut" and press the [Enter] key.
|
|
- Use []
or []
to select "Off," and press the [Enter] key.
|
|
- Use []
or []
to select "Dotted" and press the [Enter] key.
- The display returns to the character input display.
|
|
- Press the [Shift]+[Cancel] keys.
- The display returns to the character input display.
- You can check the half cut setting on the display.
|
|
Change the Full Cut Settings
The default setting is "End only."
Setting |
Details |
Print Preview |
End only
(Default Setting) |
Cuts the print media at the end of printing. |
|
Each set |
Cuts match the number of prints. |
|
[Example] Full cut for all pages printed.
- Press the [Option] key.
|
- Use []
or []
to select "Print Settings" and press the [Enter] key.
|
|
- Use []
or []
to select "Full cut" and press the [Enter] key.
|
|
- Use []
or []
to select "Each set," and press the [Enter] key.
|
|
- Press the [Shift]+[Cancel] keys.
- The display returns to the character input display.
|
If the cutter blade is becoming less sharp or half cutting is too deep, adjust the depth of the cut.
Adjustment can be set for both "Half cut" and "Full cut."
Change the Cut Depth for Half Cut
The cut depth for half cut can be set for each print media. The default setting is set to "Normal."
If
cutting is difficult depending on the material of the print media, adjust the motion of the cut.
[Example] The half cut of the label tape is too deep (or too shallow), so adjust the half cut depth.
- Press the [Option] key.
|
- Use []
or []
to select "Print adjust" and press the [Enter] key.
|
|
- Use []
or []
to select "Half Cut Depth" and press the [Enter] key.
|
|
- Use []
or []
to select "Label," and press the [Enter] key.
|
|
- Use []
or []
to select the half cut depth adjustment value, and press the [Enter] key.
- The Half Cut Depth can be set in 11 levels:
"Deep (1-5)," "Normal," and "Shallow (1-5)."
- Each time you press [],
the cut is deepened by one step.
- Each time you press [],
the cut will become shallower by one step.
|
|
- Press the [Shift]+[Cancel] keys.
- The display returns to the character input display.
|
If you make the cut depth deeper than necessary, the cutter and blade receiver will
wear out quickly.
If the half cut is too deep even when the cut depth is adjusted to the shallowest
setting, the blade receiver may be worn out. Replace the cutter and blade receiver.
Change the Cut Depth for Full Cut
The cut depth for the full cut can be set for each print media. The default setting is set to "Normal."
[Example] The full cut of the tube is not cut properly, so make the cut one step deeper.
- Press the [Option] key.
|
- Use []
or []
to select "Print adjust" and press the [Enter] key.
|
|
- Use []
or []
to select "Full Cut Depth" and press the [Enter] key.
|
|
- Use []
or []
to select "Tube," and press the [Enter] key.
|
|
- Use [] to
select "Deep 1" and press the [Enter] key.
- Full Cut Depth can be set in four levels: "Deep (1~3)," "Normal."
- Each time you press [],
the cut is deepened by one step.
|
|
- Press the [Shift]+[Cancel] keys.
- The display returns to the character input display.
|
If you make the cut depth deeper than necessary, the cutter and blade receiver will
wear out quickly.
If the situation is not improved after adjusting the cut depth for full cut, use "Forced full cut." With Forced full cut, the cut is made to the deepest point. If the situation is not improved even after using Forced full cut, replace the
cutter.
- Press the [Option] key.
|
- Use []
or []
to select "Others," and then press the [Enter] key.
|
|
- Use []
or []
to select "Forced full cut," and then press the [Enter] key.
|
|
- Select "Yes" with []
or [] and
then press the [Enter] key.
- Full cut will be performed.
|
|
- Press the [Shift]+[Cancel] keys.
- The display returns to the character input display.
|
If it does not cut well when you change the print media, adjust the motion of the cut.
Adjustment can be set for both "Half cut" and "Full cut."
If the cutter blade is becoming less sharp, adjust the depth of the cut.
Change the Motion of the Half Cut
The motion of the half cut can be set for each print media. The default setting is set to "Normal."
[Example] The half cut of the label tape is not cut properly, so the cut is made stronger.
- Press the [Option] key.
|
- Use []
or []
to select "Print adjust" and press the [Enter] key.
|
|
- Use []
or []
to select "Half Cut Motion" and press the [Enter] key.
|
|
- Use []
or []
to select "Label" and press the [Enter] key.
|
|
- Use []
to select "Intense" and press the [Enter] key.
- You can set the Half Cut Motion in two levels, "Normal" and "Intense."
|
|
- Press the [Shift]+[Cancel] keys.
- The display returns to the character input display.
|
Change the Cutting Motion of Full Cut
You can set the motion of the full cut for each print media. The default setting is set to "Normal."
[Example] The tube is not cut properly when using a full cut, so make the cut stronger.
- Press the [Option] key.
|
- Use []
or []
to select "Print adjust" and press the [Enter] key.
|
|
- Use []
or []
to select "Full Cut Motion" and press the [Enter] key.
|
|
- Use []
or []
to select "Tube" and press the [Enter] key.
|
|
- Use []
to select "Intense" and press the [Enter] key.
- Full Cut Motion can be set in two levels: "Normal" and "Intense."
|
|
- Press the [Shift]+[Cancel] keys.
- The display returns to the character input display.
|