Note: The steps listed below are specific to the MX922. For instructions for other models, click here
Steps
- Make sure the printer is turned on, and there's a sheet of A4 or Letter-sized paper loaded.
- Press the Menu button.
- Press the right arrow and the down arrow to select Setup, then press OK.
- Select Device settings, then press OK.
- Use the arrow buttons to select LAN settings, then press OK.
- Use the arrow buttons to select Confirm LAN settings, then press OK.
- Use the arrow buttons to select Print LAN details, then press OK.
- Use the arrow buttons to select Yes, then press OK to start printing.
- The printer prints a page containing your network configuration details. See document below for an example.
The following information on the machine's network setting is printed out.
Item
|
Explanations of the item
|
Setting
|
---|
Wireless LAN
|
Wireless LAN
|
Enable/Disable
|
Connection
|
Status of the Wireless LAN
|
Active/Inactive
|
MAC Address
|
MAC Address
|
XX:XX:XX:XX:XX:XX
|
SSID
|
SSID
|
SSID of the wireless LAN
|
Communication Mode
|
Communication Mode
|
Infrastructure
|
Channel
|
Channel
|
XX (1 to 13)
|
Encryption
|
Method of the Encryption
|
none/WEP/TKIP/AES
|
WEP Key Length
|
WEP Key Length
|
Inactive/128/64
|
Authentication
|
Method of the Authentication
|
none/auto/open/shared/WPA-PSK/WPA2-PSK
|
Signal Strength
|
Signal Strength
|
0 to 100 [%]
|
TCP/IP Version
|
TCP/IP Version
|
IPv4 & IPv6/IPv4
|
IPv4 IP Address
|
Selected IP Address (IPv4)
|
XXX.XXX.XXX.XXX
|
IPv4 Default Gateway
|
Default Gateway (IPv4)
|
XXX.XXX.XXX.XXX
|
Subnet Mask
|
Subnet Mask
|
XXX.XXX.XXX.XXX
|
IPv6 IP Address *1
|
Selected IP Address (IPv6)
|
XXXX:XXXX:XXXX:XXXX XXXX:XXXX:XXXX:XXXX
|
IPv6 Default Gateway *1
|
Default Gateway (IPv6)
|
XXXX:XXXX:XXXX:XXXX XXXX:XXXX:XXXX:XXXX
|
Subnet Prefix Length*1
|
Subnet Prefix Length
|
XXX
|
IPsec*2
|
IPsec setting
|
Active
|
Security Protocol*2
|
Method of the Security Protocol
|
ESP/ESP & AH/AH
|
Wireless LAN DRX
|
Discontinuous reception (wireless LAN)
|
Enable/Disable
|
Wired LAN
|
Wired LAN
|
Enable/Disable
|
Connection
|
Status of the Wired LAN
|
Active/Inactive
|
MAC Address
|
MAC Address
|
XX:XX:XX:XX:XX:XX
|
TCP/IP Version
|
TCP/IP Version
|
IPv4 & IPv6/IPv4
|
IPv4 IP Address
|
Selected IP Address (IPv4)
|
XXX.XXX.XXX.XXX
|
IPv4 Default Gateway
|
Default Gateway (IPv4)
|
XXX.XXX.XXX.XXX
|
Subnet Mask
|
Subnet Mask
|
XXX.XXX.XXX.XXX
|
IPv6 IP Address *1
|
Selected IP Address (IPv6)
|
XXXX:XXXX:XXXX:XXXX XXXX:XXXX:XXXX:XXXX
|
IPv6 Default Gateway *1
|
Default Gateway (IPv6)
|
XXXX:XXXX:XXXX:XXXX XXXX:XXXX:XXXX:XXXX
|
Subnet Prefix Length*1
|
Subnet Prefix Length
|
XXX
|
IPsec*2
|
IPsec setting
|
Active
|
Security Protocol*2
|
Method of the Security Protocol
|
ESP/ESP & AH/AH
|
Wired LAN DRX
|
Discontinuous reception (wired LAN)
|
Enable/Disable
|
Other Settings
|
Other settings
|
-
|
Printer Name
|
Printer name
|
Printer name (Up to 15 characters)
|
WSD
|
WSD setting
|
Enable/Disable
|
WSD Timeout
|
Timeout
|
1/5/10/15/20 [min]
|
LPR Protocol
|
LPR protocol setting
|
Enable/Disable
|
Bonjour
|
Bonjour setting
|
Enable/Disable
|
Bonjour Service Name
|
Bonjour service name
|
Bonjour service name (Up to 52 characters)
|
PictBridge Commun.
|
PictBridge Communication
|
Enable/Disable
|
DNS Server
|
Getting DNS Server automatically
|
Auto/Manual
|
Primary Server
|
Primary server address
|
XXX.XXX.XXX.XXX
|
Secondary Server
|
Secondary server address
|
XXX.XXX.XXX.XXX
|
Proxy Server
|
Proxy Server setting
|
Enable/Disable
|
Proxy Port
|
Specifying Proxy Port
|
1 to 65535
|
Proxy Address
|
Proxy Address
|
XXXXXXXXXXXXXXXXXXXX
|
IP Address Filtering
|
IP Address Filtering
|
Enable/Disable
|
("XX" represents alphanumeric characters.)
*1 Only when IPv6 is activated, the status of the network is printed.
*2 Only IPv6 and the IPsec setting are activated, the status of the network is printed.