This article explains how to print a Network Setting Page.  An example of the Lan Details page is attached to this article.

 

Printing Out Network Setting Information

You can print out the network settings of the printer such as its IP address and SSID.

 

Note: The steps listed below are specific to the PRO-10 and PRO-100 printers.  For instructions for other models, click here
 

•  Important  This print out contains valuable information about your computer. Handle it with care.

  1. Make sure that the printer is turned on.

  2. Load a sheet of A4 or Letter-sized plain paper.

  3. Press and hold the RESUME/CANCEL button until the POWER lamp flashes 6 times.

  4. Release the RESUME/CANCEL button.

     The printer starts printing the network setting information.

     The following information on the printer's network setting is printed out.

     Item	Explanations of the item	Setting
     Wireless LAN	Wireless LAN	Enable/Disable
     Connection	Status of the Wireless LAN	Active/Inactive
     MAC Address	MAC Address	XX:XX:XX:XX:XX:XX
     SSID	SSID	SSID of the wireless LAN
     Communication Mode	Communication Mode	Infrastructure
     Channel	Channel	XX (1 to 13)
     Encryption	Method of the Encryption	none/WEP/TKIP/AES
     WEP Key Length	WEP Key Length	Inactive/128/64
     Authentication	Method of the Authentication	none/auto/open/shared/WPA-PSK/WPA2-PSK
     Signal Strength	Signal Strength	0 to 100 [%]
     TCP/IP Version	TCP/IP Version	IPv4 & IPv6/IPv4
     IPv4 IP Address	Selected IP Address (IPv4)	XXX.XXX.XXX.XXX
     IPv4 Default Gateway	Default Gateway (IPv4)	XXX.XXX.XXX.XXX
     Subnet Mask	Subnet Mask	XXX.XXX.XXX.XXX
     IPv6 IP Address *1	Selected IP Address (IPv6)	XXXX:XXXX:XXXX:XXXX XXXX:XXXX:XXXX:XXXX
     IPv6 Default Gateway *1	Default Gateway (IPv6)	XXXX:XXXX:XXXX:XXXX XXXX:XXXX:XXXX:XXXX
     Subnet Prefix Length*1	Subnet Prefix Length	XXX
     IPsec*2	IPsec setting	Active
     Security Protocol*2	Method of the Security Protocol	ESP/ESP & AH/AH
     WPS PIN CODE	WPS PIN code	XXXXXXXX
     Wireless LAN DRX	Discontinuous reception (wireless LAN)	Enable/Disable
     Wired LAN	Wired LAN	Enable/Disable
     Connection	Status of the Wired LAN	Active/Inactive
     MAC Address	MAC Address	XX:XX:XX:XX:XX:XX
     TCP/IP Version	TCP/IP Version	IPv4 & IPv6/IPv4
     IPv4 IP Address	Selected IP Address (IPv4)	XXX.XXX.XXX.XXX
     IPv4 Default Gateway	Default Gateway (IPv4)	XXX.XXX.XXX.XXX
     Subnet Mask	Subnet Mask	XXX.XXX.XXX.XXX
     IPv6 IP Address *1	Selected IP Address (IPv6)	XXXX:XXXX:XXXX:XXXX XXXX:XXXX:XXXX:XXXX
     IPv6 Default Gateway *1	Default Gateway (IPv6)	XXXX:XXXX:XXXX:XXXX XXXX:XXXX:XXXX:XXXX
     Subnet Prefix Length*1	Subnet Prefix Length	XXX
     IPsec*2	IPsec setting	Active
     Security Protocol*2	Method of the Security Protocol	ESP/ESP & AH/AH
     Wired LAN DRX	Discontinuous reception (wired LAN)	Enable/Disable
     Other Settings	Other settings	-
     Printer Name	Printer name	Printer name (Up to 15 characters)
     WSD	WSD setting	Enable/Disable
     WSD Timeout	Timeout	1/5/10/15/20 [min]
     LPR Protocol	LPR protocol setting	Enable/Disable
     Bonjour	Bonjour setting	Enable/Disable
     Bonjour Service Name	Bonjour service name	Bonjour service name (Up to 52 characters)
     IP Address Filtering	IP Address Filtering	Enable/Disable

     ("XX" represents alphanumeric characters.)

     *1 Only when IPv6 is activated, the status of the network is printed.

     *2 Only IPv6 and the IP sec setting are activated, the status of the network is printed.