You may occasionally need information about your Wi-Fi® connection, such as your machine's IP address or signal strength.
Follow these steps to get a printout similar to the sample provided below.
These steps are specific to the PIXMA MG3620. Get instructions for other printer models.
-
Make sure that the printer is turned on.
-
Load two sheets of A4 or Letter-size plain paper.
-
Press and hold the Wi-Fi button and release it when the ON light flashes.
-
Press the Wi-Fi button again. The machine starts printing the network setting information.
Sample printout
Item | Description | Setting |
---|
Product Information | Product information | - |
Product Name | Product name | XXXXXXXX |
ROM Version | ROM version | XXXXXXXX |
Serial Number | Serial number | XXXXXXXX |
Default Password *4 | Default Password (to access Remote UI) | XXXXXXXX |
Wireless LAN | Wireless LAN | Enable/Disable |
MAC Address | MAC address | XX:XX:XX:XX:XX:XX |
WPS PIN CODE | WPS PIN code | XXXXXXXX |
Infrastructure | Infrastructure | Enable/Disable |
Connection | Connection status | Active/Inactive |
SSID | SSID | Wireless LAN SSID |
Channel *1 | Channel | XX (1 to 11) |
Encryption | Encryption method | None/WEP/TKIP/AES |
WEP Key Length | WEP key length (bits) | Inactive/128/64 |
Authentication | Authentication method | None/auto/open/shared/WPA-PSK/WPA2-PSK |
Signal Strength | Signal strength | 0 to 100 [%] |
TCP/IPv4 | TCP/IPv4 | Enable |
IP Address | IP address | XXX.XXX.XXX.XXX |
Subnet Mask | Subnet mask | XXX.XXX.XXX.XXX |
Default Gateway | Default gateway | XXX.XXX.XXX.XXX |
TCP/IPv6 | TCP/IPv6 | Enable/Disable |
IP Address *2 | IP address | XXXX:XXXX:XXXX:XXXX XXXX:XXXX:XXXX:XXXX |
Subnet Prefix Length *2 | Subnet prefix length | XXX |
Default Gateway *2 | Default gateway | XXXX:XXXX:XXXX:XXXX XXXX:XXXX:XXXX:XXXX |
IPsec *3 | IPsec setting | Active |
Security Protocol *3 | Security method | ESP/ESP & AH/AH |
Access Point Mode | Access point mode | Enable/Disable |
Connection | Connection status | Active/Inactive |
SSID | SSID | Access Point Mode SSID |
Password | Password | Password of the access point mode (8 to 10 alphanumeric characters) |
Channel | Channel | 3 |
Encryption | Encryption method | AES |
Authentication | Authentication method | WPA2-PSK |
TCP/IPv4 | TCP/IPv4 | Enable |
IP Address | IP address | XXX.XXX.XXX.XXX |
Subnet Mask | Subnet mask | XXX.XXX.XXX.XXX |
Default Gateway | Default gateway | XXX.XXX.XXX.XXX |
TCP/IPv6 | TCP/IPv6 | Enable/Disable |
IP Address *2 | IP address | XXXX:XXXX:XXXX:XXXX XXXX:XXXX:XXXX:XXXX |
Subnet Prefix Length *2 | Subnet prefix length | XXX |
Default Gateway *2 | Default gateway | XXXX:XXXX:XXXX:XXXX XXXX:XXXX:XXXX:XXXX |
IPsec *3 | IPsec setting | Active |
Security Protocol *3 | Security method | - |
Other Settings | Other settings | - |
Printer Name | Printer name | Printer name (Up to 15 alphanumeric characters) |
WSD Printing | WSD printing setting | Enable/Disable |
WSD Timeout | Timeout | 1/5/10/15/20 [min] |
LPD Printing | LPD printing setting | Enable/Disable |
Bonjour | Bonjour setting | Enable/Disable |
Bonjour Service Name | Bonjour service name | Bonjour service name (Up to 52 alphanumeric characters) |
PictBridge Commun. | PictBridge communication | Enable/Disable |
DNS Server | Obtain DNS server address automatically | Auto/Manual |
Primary Server | Primary server address | XXX.XXX.XXX.XXX |
Secondary Server | Secondary server address | XXX.XXX.XXX.XXX |
Proxy Server | Proxy server setting | Enable/Disable |
Proxy Address | Proxy address | XXXXXXXXXXXXXXXXXXXX |
Proxy Port | Proxy port specification | 1 to 65535 |
("XX" represents alphanumeric characters.)
*1 Channel may range from 1 to 11 depending on country or region of purchase.
*2 Network status is only printed when IPv6 is enabled.
*3 Network status is only printed when IPv6 and IPsec settings are enabled.
*4 Firmware version 3.000 or later required.
For support and service options, sign into (or create) your Canon Account from the link below.
My Canon Account