| Search Results |
 |
Multiple Projectors Corner Adjustment WUX7500 / WUX6700 / WUX5800
|
Corner Adjustment Projected images from multiple projectors used in overlapping projection must be precisely repositioned. Positions of each corner in the blending area can be aligned with the blending area of the reference projector. 1 On the reference projector, configure keystone (P145) and edge-blending settings, and then set the edge-blending markers to [On]. 2 Select [Install settings] > [Professional settings] > [Edge blending] > [Adjust] > [Corner adjustment]. 3 Select a point to adjust, and move it so that the image as a whole looks symmetrical. 4 As you watch the projected images, fine-tune markers of the projector you are adjusting so that they overlap the reference projector markers as much as possible.
|
|
|
Adjusting Keystone Distortion WUX7500 / WUX6700 / WUX5800
|
Adjusting Keystone Distortion Two types of correction are available: horizontal/vertical correction and corner correction. Use horizontal/vertical keystone correction to adjust image width or height
|
|
|
Using PC-Free Multi Projection WUX7500 / WUX6700 / WUX5800
|
Using PC-Free Multi Projection A JPEG image on a USB flash drive can be divided among up to nine projectors and combined into a single, large image. When projectors are connected via a wired LAN, the projector that produces the image in the upper left is called the Primary projector and the other eight, Secondary projectors. The image as a whole is controlled by the Primary projector PC-free multi projection is not available over a wireless LAN. This feature is available with the following number of projectors and layout patterns. The projector you assign as the Primary projector, identified in the layout pattern as [1], always projects the upper-left image. Set up the projectors as follows. 1 On each projector, configure installation and image adjustment settings such as edge blending and keystone correction to blend overlapping areas. 2 Connect the projectors with LAN cables and set [Network (wired/wireless)] to [On/Off] or [On/On (Pj AP)] 3 Configure some projectors as Secondaries. Select [Input settings] > [PC-free multi projection] > [Mode setting] > [Secondary]. Complete this setting on each Secondary projector 4 Configure one projector as the Primary projector. (1) Select [Input settings] > [PC-free multi projection] > [Mode setting] > [Primary]. ( 2 ) Configure the following settings in [PC-free multi projection].
|
|
|
Turning the Projector Off WUX7500 / WUX6700 / WUX5800
|
1 Press the POWER button. 2 When this window is displayed, press the POWER button again. After you turn the power off, the projector will enter standby mode once it cools down.
|
|
|
Projecting from Multiple Projectors at Once (Edge Blending) WUX7500 / WUX6700 / WUX5800
|
Overlapping edges of images from multiple projectors used together can be blended to make the overall image more seamless. This feature is called edge blending. Follow these steps for basic edge blending with two projectors side by side.
|
|
|
Menu System settings WUX7500 / WUX6700 / WUX5800
|
Menu screen when the input signal is HDMI Menus that are not available are grayed out or hidden. User screen settings Capture a logo and specify logo display settings. Logo capture Registers the current image as a user logo. Registered user logos can be shown when no signal is received, when the BLANK button is pressed, or as the startup image. Only images at an aspect ratio of 16:10 can be registered as user logos. Logo position Specify the position of registered user logos. You can specify the position after a logo has been registered. Choose from upper left, upper right, center, lower left, or lower right. No signal screen Customize the screen shown when no input signals are received. Screen when blank Select the screen shown when projection is temporarily blanked out by pressing the BLANK button on the remote control. Projector on Select a logo to project after startup until input signals can be projected. On screen Specify display details for on-screen menus, help , and warning or precaution icons. Menu position Reposition menu display. Choose from upper left, upper right, center, lower left, or lower right. Only [Center] is available when edge blending is used. Other display positions are grayed out and not available. Menu display time Extend menu display from the standard 10 or 30 seconds to 3 minutes. The following display times are also changed. Guide Shows the guide screen.
|
|
|
Connecting Other Equipment WUX7500 / WUX6700 / WUX5800
|
DisplayPort Connections Analog PC- 2 / COMPONENT Connections LAN / HDBaseT Connections
|
|
|
PJLink WUX7500 / WUX6700 / WUX5800
|
• The projector conforms to Class 2 as defined in PJLink standards established by the Japan Business Machine and Information System Industries Association (JBMIA). This projector supports all commands that are defined by PJLink Class 2 , and PJLink compatibility has been verified.
|
|
|
Controlling the Projector from a Computer WUX7500 / WUX6700 / WUX5800
|
1 Turn on the computer and projector. 2 Launch a web browser, enter “http://(projector IP address)” in the address bar, and press the Enter key. The projector web screen appears.
|
|
|
Projecting Images on a USB Flash Drive WUX7500 / WUX6700 / WUX5800
|
1 Insert a USB flash drive in the USB port. 2 Press the INPUT button to select [USB]. 3 In the USB file browser, select a file for projection.
|
|
