The steps listed below are specific to the iP110. For instructions for other models, click here.
You can print out the current network settings of the printer.
This print out contains valuable information about your computer. Handle it with care.
-
Make sure that the printer is powered on.
-
Load a sheet of A4 or Letter-sized plain paper.
-
Press and hold the RESUME/CANCEL button, then release the button when the POWER lamp flashes 6 times.
The printer starts printing the network setting information.
The following information on the printer's network setting is printed out.
Item | Explanations of the item | Setting |
---|
Wireless LAN | Wireless LAN | Enable/Disable |
Connection | Connection status | Active/Inactive |
MAC Address | MAC Address | XX:XX:XX:XX:XX:XX |
SSID | SSID | SSID of the wireless LAN/SSID of the access point mode |
Password | Password | Password of the access point mode (8 to 10 alphanumeric characters) |
Communication Mode | Communication Mode | Infrastructure/Access Point Mode |
Channel *1 | Channel | XX (1 to 13) |
Encryption | Method of the Encryption | none/WEP/TKIP/AES |
WEP Key Length | WEP Key Length | Inactive/128/64 |
Authentication | Method of the Authentication | none/auto/open/shared/WPA-PSK/WPA2-PSK |
Signal Strength | Signal Strength | 0 to 100 [%] |
TCP/IP Version | TCP/IP Version | IPv4 & IPv6/IPv4 |
IPv4 IP Address | Selected IP Address (IPv4) | XXX.XXX.XXX.XXX |
IPv4 Default Gateway | Default Gateway (IPv4) | XXX.XXX.XXX.XXX |
Subnet Mask | Subnet Mask | XXX.XXX.XXX.XXX |
IPv6 IP Address *2 | Selected IP Address (IPv6) | XXXX:XXXX:XXXX:XXXX XXXX:XXXX:XXXX:XXXX |
IPv6 Default Gateway *2 | Default Gateway (IPv6) | XXXX:XXXX:XXXX:XXXX XXXX:XXXX:XXXX:XXXX |
Subnet Prefix Length *2 | Subnet Prefix Length | XXX |
IPsec *3 | IPsec setting | Active |
Security Protocol *3 | Method of the Security Protocol | ESP/ESP & AH/AH |
WPS PIN CODE | WPS PIN code | XXXXXXXX |
Wireless LAN DRX | Discontinuous reception (wireless LAN) | Enable/Disable |
Other Settings | Other settings | - |
Printer Name | Printer name | Printer name (Up to 15 alphanumeric characters) |
WSD | WSD setting | Enable/Disable |
WSD Timeout | Timeout | 1/5/10/15/20 [min] |
LPR Protocol | LPR protocol setting | Enable/Disable |
Bonjour | Bonjour setting | Enable/Disable |
Bonjour Service Name | Bonjour service name | Bonjour service name (Up to 52 alphanumeric characters) |
PictBridge Commun. | PictBridge Communication | Enable/Disable |
DNS Server | Getting DNS Server automatically | Auto/Manual |
Primary Server | Primary server address | XXX.XXX.XXX.XXX |
Secondary Server | Secondary server address | XXX.XXX.XXX.XXX |
Proxy Server | Proxy Server setting | Enable/Disable |
Proxy Port | Specifying Proxy Port | 1 to 65535 |
Proxy Address | Proxy Address | XXXXXXXXXXXXXXXXXXXX |
("XX" represents alphanumeric characters.)
*1 Depending on the country or region of purchase, one of the channels from 1 to 11 is printed.
*2 Only when IPv6 is enabled, the status of the network is printed.
*3 Only when IPv6 and the IPsec setting are enabled, the status of the network is printed.
If your product issue was not resolved after following the steps above, or if you require additional help, please create or log in to your Canon Account to see your technical support options.
Or if you still need help, visit our Canon Community by clicking the button below to get answers:
____________________________________________________________________________________________